Does 7-Way Molded Trailer End # 54006-009 Come with Heat Shrink Butt Connectors

Question

Question:

I just wanted to clarify that this comes with the heat-shrink wire connectors, or do I need to purchase these separately? You guys have the BEST how-to videos! Thanks for your help!

asked by: Tracy M

0

Expert Reply:

7-Way Molded Trailer End # 54006-009 does not come with the heat shrink butt connectors. You can add some for the smaller gauge wires using # DW05744-5. For the larger gauge power and ground wires you can use # DW05745-5.

expert reply by: Michael H

0

Answer 1

7-Way trailer connectors have a male and a female side and the male installs on the trailer side and the female on the tow vehicle. That's why you are seeing them labelled differently. The part #54006-009 is a trailer side 7-way like it sounds…

view full answer...

Answer 2

For a replacement mounting bracket, you can use part #FRCBRKT-BL. This is compatible with all Furrion Vision S RV cameras that use the shark fin style housing, including your model FOS48TAPK-BL, which has been replaced by #FOS43TASF.

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 8

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

Either way is correct. It depends on if you want to keep the semi-style 7-Way (if you need to tow that type of trailer) or if you will never be towing a semi-trailer. If you need to keep the 7-Way semi active on the truck, then you would need to make…

view full answer...

Answer 12

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...