Fifth Wheel Hitch for 2017 Ford F-350 Factory Rail Kit Towing Trailer with Tapered Nose

Question

Question:

I just bought a Montana 3120RL and intend to buy a new 2017 Ford F350 Super Duty with a 6.75foot box and the Ford puck system. Can I use the 20k Reese hitch non-slider, sinse the Montana has the rounded front to nose to avoid contact with the cad on cornering?

asked by: Dave F

1

Helpful Expert Reply:

Since your Montana 3120RL has the tapered nose design you can use a fixed hitch like the Reese M5 Hitch part # RP30921 with your short bed 2017 Ford F-350 with factory rail kit. Since the nose is tapered you don't have to use a slider hitch.

This is the correct hitch for the factory Ford rail kits like what you have as well.

expert reply by: Jameson C

1

Answer 1

If you currently have the MORryde SRE4000 Cushioned Equalizers then you will want to use the MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension part #MR33WR. This is a bolt-on kit which will work to provide extra support to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 8

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 12

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...