Install Instructions for Hopkins Backup Sensor System # HM60100VA

Question

Question:

Im interested in purchasing this item, HM60100VA, but would like to know more information on how to install the product. Can you send me the install instructions to see how easy or difficult this may be? Thank you!

asked by: Michael K

0

Expert Reply:

I attached two pictures that are the install instructions for the Hopkins BackUp Camera part # HM60100VA that you referenced as well as a link to an install video down below for you to check out.

expert reply by: Jameson C

0

click to enlarge

Bruce

8/6/2020

HM60100VA will it go on tags that are off center 2020 Ram Promaster 1500

Reply

Jon G.

8/17/2020

Definitely! The Hopkins Backup Sensor System # HM60100VA simply installs wherever your license plate installs. The sensors will beep when they detect things up to 5-1/2' away so the driver's side will have a little further reach away from the vehicle because of the offset.

Reply

Answer 1

The Hopkins Backup Sensor system #HM60100VA should fit as it is designed to fit standard mirror plate dimensions, but to be sure you can compare the measurements of this with the current license plate frame you have to see if it would be too big. The…

view full answer...

Answer 2

The Hopkins License Bracket Mount Backup Sensor System #HM60100VA is a universal-fit item intended to fit a wide range of vehicles. Its fit is not specific to one type or style of vehicle. It mounts using the standard hole spacing for your license…

view full answer...

Answer 3

The Hopkins Backup Sensor System, item # HM60100VA, is designed to detect items directly behind the vehicle and straight out. I spoke with my contact at Hopkins and he explained that the backup sensor would detect items at the ground for a distance…

view full answer...

Answer 4

Yes, the Hopkins Backup Sensor System - Audible Alert - License Bracket Mount, item #HM60100VA, can be mounted upside down. However, if your rear bumper protrudes out below the license plate, then the backup sensor will not be able to pickup items…

view full answer...

Answer 5

The camera is not available by itself for Hopkins back up camera system #HM60195VA. I think you might have seen #HM60100VA which does not include a camera, just back up sensors. But if you did have 2 cameras you could use one monitor for both but…

view full answer...

Answer 6

The sensors on the Hopkins Backup Sensor System part #HM60100VA have a viewing angle of 110 degrees. The sensors can detect objects up to 5.5' away. There are three ranges of detection: red 0-1.5', yellow 1.5'-3.5', and green…

view full answer...

Answer 7

I do have one option for you since the Replacement BOLT Lock Cylinder #BL709231 is for the Tailgate Handle with BOLT Lock #BL5922987 and will not replace the factory lock on your 2015 Chevrolet Silverado 1500WT. For that cylinder you will need to…

view full answer...

Answer 8

The Hopkins Backup Sensor System #HM60100VA that you referenced does not require drilling so it would be a great solution for your 2016 Kia Optima that you do not want to drill into.

view full answer...

Answer 9

I do have an option for you but the Hopkins Backup Sensor System part #HM60100VA will only work effectively if mounted in the center of the vehicle and not with offset mounted license plates like the one on your Jeep Wrangler. Instead, I recommend…

view full answer...

Answer 10

The Hopkins Backup Sensor system #HM60100VA should fit as it is designed to fit standard mirror plate dimensions, but to be sure you can compare the measurements of this with the current license plate frame you have to see if it would be too big. The…

view full answer...

Answer 11

The pressure relief valve on your Furrion RV Tankless Water Heater #FR68SR could potentially be faulty from the manufacturer but before you make a warranty claim to Furrion you should test to see if the valve is correctly seated. Pull the lever on…

view full answer...

Answer 12

The Furrion RV Tankless Water Heater part #FR98SR has an inlet working pressure of 10-65 psi. Therefore, the minimum is 10 psi.

view full answer...

Install Instructions for Hopkins Backup Sensor System # HM60100VA

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching