Will Hopkins License Bracket Mount Backup Sensor System # HM60100VA Fit 2014 Ford F-150

Question

Question:

Hopkins Backup Sensor System - Audible Alert - License Bracket Mount Will that fit on 2014 F150 with chrome bumper ?

asked by: Carey G

1

Helpful Expert Reply:

The Hopkins License Bracket Mount Backup Sensor System # HM60100VA is a universal-fit item intended to fit a wide range of vehicles. Its fit is not specific to one type or style of vehicle. It mounts using the standard hole spacing for your license plate.

I have linked a photo of this unit showing its overall dimensions and also a video showing a typical installation.

expert reply by: Adam R

1

click to enlarge

Answer 1

Yes, the Hopkins Backup Sensor System - Audible Alert - License Bracket Mount #HM60100VA will work with metal license plates.

view full answer...

Answer 2

The Hopkins Backup Sensor system #HM60100VA should fit as it is designed to fit standard mirror plate dimensions, but to be sure you can compare the measurements of this with the current license plate frame you have to see if it would be too big. The…

view full answer...

Answer 3

I attached two pictures that are the install instructions for the Hopkins BackUp Camera part #HM60100VA that you referenced as well as a link to an install video down below for you to check out.

view full answer...

Answer 4

Yes, the Hopkins Backup Sensor System item #HM60100VA, can be mounted upside down. However, if your rear bumper protrudes out below the license plate, then the backup sensor will not be able to pickup items that are low to the ground. The sensor…

view full answer...

Answer 5

The distance of 5-1/2 feet is measured from the sensors on the Hopkins #HM60100VA. If installing this on your 2020 Silverado means you have a few inches between where the sensors are located and the edge of your bumper then you would need to account…

view full answer...

Answer 6

The Hopkins Backup Sensor System - Audible Alert - License Bracket Mount, #HM60100VA, is designed to be wired in with the reverse light circuits so it will only be operating when in reverse and not while towing or parked. If you are still concerned…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Will Hopkins License Bracket Mount Backup Sensor System # HM60100VA Fit 2014 Ford F-150

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching