Recommended Ball Mount Rated for 14,000 Pounds to Fit a 2 inch Trailer Hitch Receiver

Question

Question:

Looking for a ball mount for a 2 inch receiver and at least 14k tow capacity for use with my RV.

asked by: Larry M

0

Expert Reply:

For a high capacity 2 inch ball mount I recommend looking at a Gen-Y # 325-GH-515.

This particular one is rated up to 16,000 pounds and offers up to 10 inch drop or rise. Then for a tongue weight scale, should you need one, use part # e99044.

expert reply by: Charles S

0

Answer 1

To determine if you have the correct system for your trailer tongue weight, you should determine the fully loaded and ready to tow tongue weight of your trailer. The weight of any gear stowed behind the rear axle of the tow vehicle also needs to be…

view full answer...

Answer 2

The Edge Insight CTS, #EP84130, the data parameters you can monitor include: Battery Voltage Intake Air Temperature (IAT) Engine Oil Pressure (EOP) Engine Coolant Temperature (ECT) Engine Oil Temperature (EOT) Transmission Fluid Temperature (TFT)…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 9

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...