Is Camco Vent Cover Compatible with Fan-Tastic Vent Fan?

Question

Question:

Will this fit with Fantastic vent fan?

asked by: Daryl

0

Expert Reply:

The Camco RV and Enclosed Trailer Roof Vent Cover # CAM40453 is compatible with all standard size roof vents including the Fan-Tastic vent fans like # FV801250. I've attached a video of the installation to assist.

expert reply by: Jason S

0

Answer 1

Hey David, thank you for the photos and explanation! That is most definitely an Aries Grille Guard, and if it came off of a 2006 Chevy Silverado 1500 then we're looking at the part #AA4059-2 which will also fit your 2003 model by using the…

view full answer...

Answer 2

Actually the type of roof vent cover you need to attach to the vent cover brackets of your Maxxair 4951KS like part #MA00-04500K is the part #MA00-955003 which uses those brackets with the included cotter pins of the cover.

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

We don't have the specific number but what I think will be more helpful for you is the distance from the rear most portion of the bumper to the hitch pin hole. Which for the #41932 that dimension is 1-1/2 inches. Check out the picture I attached…

view full answer...

Answer 6

Yes you are correct the Replacement MaxxFan Plus 4-Speed Roof Vent with White Lid #MA00-04751KSX is the right replacement and measures 18 1/8" long and 16 1/2" wide, which is the same measurements as your current MaxxFan Plus Roof Vent w/…

view full answer...

Answer 7

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 10

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 11

90-120 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...