Lug Nut Torque for a Trailer Wheel

Question

Question:

I have a 4300 lb trailer with ST 205/75R15 tires. The wheels have 5- 1/2inch lugs. I believe the sticker on the rim says 90-120 ft/lbs. Could you please confirm this, Thanks.

asked by: Art

1

Helpful Expert Reply:

90-120 ft lbs of torque is probably about right for your trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher.

expert reply by: Jameson C

1

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference is the color coding of the wire functions for the two 7-way kits part #54006-057 and #54006-009 that you referenced. The part #54006-009 is going to have the wiring colors that are most common on trailers with 7-ways whereas the…

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 4

There are several ways that you can cut off the power to your trailer brakes. The easiest option would be to simply unplug your brake controller. If the brake controller is disconnected, the brakes will not receive power. If your brake controller…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 12

The Tekonsha T-One #118304 and Curt T-Connector #C55580 Vehicle Wiring Harnesses are very similar. These are both custom fit wiring harnesses that include a tail light converter, which is required for your 2007 Toyota Sienna because the brake and…

view full answer...

Lug Nut Torque for a Trailer Wheel

Product Page this Question was Asked From

Continue Researching