Replacement Release Latch Assembly for Roadmaster Falcon 2 Towbar

Question

Question:

The release latch has been lost off of my falcon 2 hitch can I buy another one?

asked by: Jerry W

0

Expert Reply:

For your Roadmaster Falcon 2 Tow Bar # RM-520, the Replacement Storage Latch # RMB001353 is most likely what you are looking for. If you are wanting the entire assembly you will want the Replacement Shank Assembly for Roadmaster Falcon 2 and Blackhawk 2 Towbars - Black # 910019-20B.

expert reply by: Jason S

0

Answer 1

There are a few repair parts for the Blackhawk 2 tow bar, #RM-422, but not all components can be repaired. I have included the replacement parts we have available below. - Roadmaster Square Plug #RM-200140-40 - Replacement Base Pins with Chains and…

view full answer...

Answer 2

We do have the Complete Repair Kit for Roadmaster Sterling Tow Bar #RM-910003-30 as the Kit #RM910003-85 is for Falcon and Blackhawk tow bars. We also have the following parts if they are damaged and need replaced on your tow bars. Inner Arm Bushing…

view full answer...

Answer 3

The front end of the Falcon All Terrain tow bar, #RM-522, is #910019-20. This is the part that fits in the actual hitch on the tow vehicle. If you are talking about the bar at the other end that fits between the 2 tow bar arms and attaches to the…

view full answer...

Answer 4

We have exactly what you need to flat tow your 2013 GMC Sierra 1500 behind your motorhome. We do not have an all inclusive kit that has everything, but what I can do is list each part that you will need. I will also include a brief description of…

view full answer...

Answer 5

In order to flat tow a 2012 Chevrolet Silverado you will need base plates, a tow bar, flat-tow wiring harness, and safety cables. In some states a supplemental braking system is also needed though this is not a required component. I have attached…

view full answer...

Answer 6

I would be happy to help you set your 2012 GMC Sierra 2500HD up for flat towing. I total understand there are a lot of options and the manufacturer's parts sometimes do not like to work together. To flat tow your Sierra you will need the…

view full answer...

Answer 7

To flat tow your 2010 Chevy Silverado 1500 you will need to first start with a base plate kit. For that the most popular option is the Roadmaster #3154-3. In addition to the base plates, you will also need a compatible tow bar, safety cables,…

view full answer...

Answer 8

I do have a list of parts needed to flat-tow a 2009 GMC Sierra 1500 but guidelines will be outlined in the owner's manual so I encourage you to look here for yourself. Generally speaking, 4WD models are good to go as is but 2WD models require the…

view full answer...

Answer 9

To flat tow your 2013 Chevy Silverado you'll need a tow bar, base plate, braking system, tow bar wiring kit, and safety cables. I have the following recommendations for you listed below: Tow Bar: etrailer XHD Non-Binding Tow Bar for Roadmaster…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 12

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...