Is a RV Waste Valve Extension Available That is Longer Than 5 Inches?

Question

Question:

I have a Avion trailer and it appears a 5” extension inadequate to clear black water valve. Can I use two extensions or is a longer extension available and more desirable? I prefer the clear view visibility for monitoring waste dumping with the Sewer Solution.

asked by: Elwood H

1

Helpful Expert Reply:

There is an extension that is longer than 5" which will work for you. The Valterra Clearview Extension # T1022 is 10" long and otherwise the same as the 5" Valterra extension you referenced. I've left a link to a video review of the part for you to take a look at as well.

expert reply by: Kyle S

1

Answer 1

The Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter #T1001VP is 5/8" thick.

view full answer...

Answer 2

The width of the smaller opening on the Valterra Double Rotating Waste Valve #T81 that you referenced is 1-1/2 inches and the width of the larger opening on the other side is 3 inches. These sizes are the standard sizes found on RV valves so most…

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 4

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 12

To wire two 6-volt batteries in series to produce 12-volts, you would connect the load to the positive terminal of battery #1. Connect the negative terminal of battery #1 to the positive terminal of battery #2. Ground the negative terminal of battery…

view full answer...