Will Bumper Cover Fit Over Curt Hitch Installed on 2015 Buick Enclave

Question

Question:

If being installed on a 2015 Buick Enclave will the fascia cover fit back onto the bumper to cover the hitch after installation?

asked by: Charlie

0

Expert Reply:

Yes, when we installed the Curt hitch part # 13424 on a similar 2015 Buick Enclave we were able to reinstall the cover as you can see in the attached install video below.

expert reply by: Jameson C

0

Answer 1

We have everything you'll need to tow a small cargo trailer with your 2017 Buick Enclave. The first thing you need is a hitch like the etrailer #e98863 which has the 5,000 lb trailer weight capacity you are wanting and is also hidden behind the…

view full answer...

Answer 2

The Curt Class III Receiver Hitch #13424 referenced in your question, which is confirmed to fit your 2017 Chevy Traverse, does require that the fascia door panel be removed during installation. Once the trailer hitch is installed, it is unlikely that…

view full answer...

Answer 3

Sounds like you have a roll pan bumper installed on your 2006 GMC Sierra based on what you described which we have hitch fits for like with the etrailer part #e82AR which will fit behind the rear license plate bracket of the roll pan bumper like the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Will Bumper Cover Fit Over Curt Hitch Installed on 2015 Buick Enclave

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching