Does Pro Series Detachable Caster Swivel?

Question

Question:

PS1400750340 Does it swivel? Cant quite tell from the pics if there are bearings in the base allowing the base to swivel. Thanks

asked by: Richard H

1

Helpful Expert Reply:

Yes, the Pro Series 6" Detachable Caster # PS1400750340 does swivel. If you check out the video I've linked for you, it will display this at about the 0:20 mark.

This caster is designed to fit jacks with 2" tubing and has a 1,200 lbs rating.

expert reply by: Kyle S

1

click to enlarge

Answer 1

There are a few different ways to measure for the correct trailer jack wheel. We do not have a jack wheel with a 1-5/8 inch shaft, but we may be able to find the correct replacement wheel based on the diameter of your jack tube. If you can send me…

view full answer...

Answer 2

I have looked through the various jack casters we offer, and a 6 inch diameter wheel is the smallest one that is offered. It sounds to me as if you need a jack that has a shorter distance between the bottom of the mount and the bottom of the outer…

view full answer...

Answer 3

I went out to the warehouse to measure the Pro Series Round, A-Frame Jack, #PS1401000303. The outer tube is 2-1/4 inches in diameter. The inner tubing is about 1.97 inches in diameter. This jack does not come with a wheel or footplate. For a wheel,…

view full answer...

Answer 4

The tube diameters on the Pro Series 6 Inch, Detachable Caster w/ Pin, part #PS1400750340, is 2 inch inside diameter and 2-1/4 inch outside diameter. The down tube on a 2 inch jack will fit inside the 2 inch tube on the caster. You will need to make…

view full answer...

Answer 5

You can still use the Pro Series jack wheel #PS1400750340. It will just be a little big on the smaller jack tube.

view full answer...

Answer 6

There are no bearings in the Pro Series 6", Detachable Caster #PS1400750340 that you referenced. It's basically just a bushing like you mentioned.

view full answer...

Answer 7

Based on the 1-1/8" diameter x 1/2" thick measurements you provided of your current gears, the Replacement Fulton Gear Kit #F0933302S00 would be the correct gear kit for your older Fulton jack as it includes two bevel gears that are…

view full answer...

Answer 8

Installing the #F0933302S00 gears is fairly easy but without proper guidance I can see how it would be pretty difficult, You will need to remove the cap at the top of the jack. The handle and gear are held in place with a roll pin. Remove the pin.…

view full answer...

Answer 9

I do have an option for you to replace the bottom plate of your trailer jack with a wheel assembly. The option I have is the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks - 1,200 lbs #PS1400750340. This corrosion-resistant,…

view full answer...

Answer 10

The beveled gear kit that you have referenced, #F0933302S00, is designed for Fulton jacks with capacities ranging from 800 to 1,200, so this should be the correct set for your 1,000 pound model. To make sure, you can compare the measurements of the…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Does Pro Series Detachable Caster Swivel?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching