Tire Chain Recommendation for 2010 Toyota Sequoia

Question

Question:

I have a 2010 Toyota Sequoia I need snow chains for elk hunting in December. I expect snow and mud potentially.

asked by: Brian K

0

Expert Reply:

For both of the standard tire sizes for your 2010 Toyota Sequoia of 275/65-18 and 275/55-20 the same tire chain sizes are listed. So for either size I would recommend the part # TC2327 if you have an Class S chain requirement (see owners manual). Or, if you don't and you want max mud traction the part # TC2439 would be really great with the bigger twisted links.

expert reply by: Jameson C

0

Answer 1

I am far from an expert on snowmobiles but one would have to think such a large truck with the correct tires and chains would be able to make it through up to 2' of snow assuming you have clearance on the vehicle. In regards to the type of tire…

view full answer...

Answer 2

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Most of the time when a tow setup is porpoising with a weight distribution system all you have to do is add a bit more spring bar tension to minimize the porpoising. With an Equalizer system you would need to angle the spring bars down further to add…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 11

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Tire Chain Recommendation for 2010 Toyota Sequoia

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching