Recommendations to Tow a Trailer Level with a 2011 Mazda 3
Question:
I am looking into a hitch for my sons Mazda 3 and the Curt hitch has a height of 10 1/4. I need to reach a height of 19inch to my sons motorcycle trailer tongue height. The most raise I see for 1 1/4 hitch is 5 inches. So I am guessing its close to 7 inches with ball which puts me 2 inches short. Do you have any suggestions on what I can do? Thanks.
asked by: Jason S
Expert Reply:
Brophy ball mount # BM96 has a 5-1/2 inch rise so that will get you 1/2 inch closer. You would not add the height of the ball though because the coupler on the trailer covers the ball so the ball height is a non-factor. The only other thing you can do is lower the height of the trailer.
If you do think lowering the trailer in the back is the way to go then you may be able to use an over/under conversion kit if:
The trailer leaf spring stack is currently mounted above the axles
The trailer uses double-eye springs
And the trailer has 2-3/8 inch or 3 inch diameter round axles
For a 2-3/8 inch round axle use # K71-384-00 and for a 3 inch diameter axle use # K71-385-00.
If you cannot use an over/under conversion kit then the only other way to lower the height of the trailer is to have the old suspension hangers cut off and new, shorter ones welded on by a qualified professional welder. I have included a link to the hanger main page for you.
Products Referenced in This Question
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Brophy
more information >
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 2-3/8 Inch
- Single Axle
- Dexter
more information >
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Suspension Parts
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 3 Inch
- Dexter
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
- Video: Curt Fusion Ball Mount Review C45152
- Search Results: 118420
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Ball Mount for 2" ATV Hitches - 2" Ball and Clevis Bar - 1/4" Rise
- Shop: 2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Shop: Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommended Hitch for a 2024 Toyota Grand Highlander
- Search Results: trailer hitch wiring
- Video: Choosing the Right Brake Controller
- Shop: Brake Controller
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Article: Trailer Wiring Diagrams
- Shop: Roof Rack
- Search Results: brake controller
- Video: etrailer Hitch Pin Alignment Collar Review
- Shop: Suspension Enhancement
- Search Results: trailer brake controller