Lift Brackets for an Older Reese V5 WD System Rated for 750 lbs

Question

Question:

can I use an older Reese V5 #750 lb. straight trunnion with chains on a new trailer with a 1200lb tongue weight. If so I need new hooks for the trailer which one would work? thanks

asked by: Steve

0

Expert Reply:

The replacement lift bracket that you will want to use with your Reese V5 Weight Distribution (WD) system is part # RP21501. If you need new chains you can use either part # 55630 or part # 3216. My contact at Reese confirmed these fits.

When choosing a WD system for your towing setup you will need to make sure that the Total Tongue Weight (TTW) of your setup falls in the middle of the Tongue Weight (TW) range of your WD system. You can find your TTW by adding the TW of your fully loaded and ready-to-go trailer along with the weight of any cargo behind the rear axle of your tow vehicle. Keep in mind that a properly loaded trailer will have a TW that is 10-15% the weight of the loaded trailer.

Since your current V5 WD system is rated for a max of 750 lbs and just the TW of your trailer is 1,200 lbs you will need to get a new WD system. The V5 that you have will not be effective on a heavier trailer.

I recommend going with the Reese Strait-Line WD System as it uses the chain hangers along with sway control cams which work to prevent sway instead of correct it after it has already started. If your loaded TW alone is 1,200 lbs then I recommend part # RP66075 which has a TW range of 1,000 lbs - 1,700 lbs. It doesn't come with a shank so you will need to use either # RP54976 or # RP54977. You will also need to use a Hitch Ball with a 1-1/4 inch shank. The Curt # C40085 is a great option because it can handle the higher weight ratings.

I have also linked some review videos and helpful articles that you can check out.

expert reply by: Jon G

0

Answer 1

The old Reese V-5 weight distribution system is not rated by the vehicle. It will be compatible with vehicles and trailers determined by the loaded tongue weight of the trailer along with any any cargo behind the rear axle of the towing vehicle.…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Lift Brackets for an Older Reese V5 WD System Rated for 750 lbs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching