Hitch Receiver Needed to Install on Inside Frame of a 2003 Freightliner Sprinter

Question

Question:

Hitch must be bolted on inside the frame as there is not enough room outside because of the lp gas tank. I ordered one last year and it would not bolt up because it mounted on the outside of the frame. hitch for 2003 freightliner motor home single wheels with lp gas tank and generator in the rear.

asked by: James S

1

Helpful Expert Reply:

The Curt Trailer Hitch Receiver # 14250 that you referenced does mount on the inside of the trailer frame, but it does require bolts to be run through from the outside of the frame (see attached picture).

You will need to make sure that you have room on your frame as this is the best option for you. The only other options mount on the outside of the frame on your 2003 Freightliner Sprinter.

I have linked the installation instructions for you to check out.

If you let me know what you will be using the hitch receiver for I will be happy to make some recommendations for you.

expert reply by: Jon G

1

click to enlarge

Answer 1

We have the Bearing Buddy Bearing Protectors #BB1968SS that fit a hub bore of 1.968 which is likely the size you have. The measurement may be slightly off based on the outside temperature as steel can expand and contract based on temperature.

view full answer...

Answer 2

The spare tire retainer would almost certainly interfere with installing the #75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt #13250 class III hitch will avoid the spare tire retainer, as shown…

view full answer...

Answer 3

The charging circuit on a vehicle 7-way style connector, the one that would deliver a maintenance charge to the trailer battery while you tow, is completely separate from the 4-wire brake controller wiring. This trailer charging circuit is usually…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Hitch Receiver Needed to Install on Inside Frame of a 2003 Freightliner Sprinter

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching