Do Trailer Wheel Studs have Weight Capacities

Question

Question:

6 lug wheel with 5500-6000lbs boat trailer hub replace with RG03-080 . Its good? Im. Ordered the rg03-080

asked by: Song K

1

Helpful Expert Reply:

If the wheel stud part # RG03-080 is the correct dimensions for your hub then it's going to work well. These don't have a specific weight capacities but if they are the correct size and are going to be used on a trailer these will work.

expert reply by: Jameson C

1

Answer 1

Hubs for 7K axles could use either 1/2 inch or 9/16 lug nuts, so you'll want to measure the diameter of the wheel studs. For 1/2 inch studs, I'd recommend the #12CLN. For 9/16 inch studs, use #LHLR110.

view full answer...

Answer 2

It appears that the HydraStar Disc Brake Kit #HSE7K-T1 is the correct kit for your 2021 Vanleigh Vilano 320GK. To verify this you can find the axle serial numbers and send that information to me so I can verify all the components are correct.…

view full answer...

Answer 3

This sounds like the trailer brakes are not receiving the signal from the brake controller when you apply the brakes. I believe what is happening is that you may have a loose, broken, or inaccurate connection on the red wire from the brake…

view full answer...

Answer 4

Sounds like your brake controller will apply your trailer brakes if you apply the manual override lever but not when you press the brake pedal. This is a fairly common problem and the solution is the red wire of the brake controller. Make sure it…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Do Trailer Wheel Studs have Weight Capacities

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching