Timbren Kit Fit Recommendation for 2007 Chevy Silverado Classic 2500HD

Question

Question:

I have a 2007 2500 hd classic chevy diesel pu, that Im wanting to install a timbren ses kit on. It looks like I have 7 1/4 inches between frame and jounce stop. Will the standard kit fit my truck giving me 1 to 1 1/2 in clearance? Will order later in week as Im at a lake camping. Thanks

asked by: Larry W

0

Expert Reply:

For your 2007 Chevy Silverado 2500HD Classic the Timbren kit you need is the part # TGMRCK25S. Since you have the factory suspension on the truck this kit will fit and work well.

I attached an install video for this kit on a 2007 Chevy Silverado 2500HD very similar to yours.

expert reply by: Jameson C

0

Answer 1

For body lifts like what you have Timbrens work just fine as-is without needing type of adapter or spacer. That means the part #TGMRCK25S will fit your 2008 GMC Sierra and work well.

view full answer...

Answer 2

Timbrens would be the way to go since you are hauling quite a bit of weight. So for your 2008 Chevy Silverado 2500 you'd want the part #TGMRCK25S which can give you up to an additional 6,000 lb of suspension support. You should note that this kit…

view full answer...

Answer 3

The GVWR of a vehicle is set in stone. There is nothing you can do to increase the capacity short of replacing the axle, suspension, and other load bearing and drive train components. What suspension enhancement like #TGMRCK25S does is help support…

view full answer...

Answer 4

The suspension enhancement option I recommend for your 2008 Chevy Silverado 2500 is the SumoSprings Rebel Custom Helper Springs #SSR-201-40-2. These are going to do a fantastic job to help control your Chevy when towing your 5th wheel because they…

view full answer...

Answer 5

The Timbren Rear Suspension Enhancement System #TGMRCK25S is a correct fit for your 2005 Chevrolet Silverado 2500 whether it is a 2WD or a 4WD version. This kit will install without need for the included 7/8-inch thick spacers UNLESS the truck has a…

view full answer...

Answer 6

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Answer 7

I went out to our warehouse and measured an overall height with the mounting bracket of 5 inches for the Timbren Rear Suspension Enhancement System #TTORSEQ. Timbren recommends having a 1/2 inch to 1-1/2 inches between the spring and the axle when…

view full answer...

Answer 8

Using a spacer kit like the #T68MR to allow one side of the truck's suspension to engage sooner will give you more support on that side but since it's hard to say if that will happen to be the sweet spot you are looking for in terms of…

view full answer...

Answer 9

Yes, The Timbren Spacer #T68MR will work with The Timbren Suspension Enhancement #TGMRTT35D on your 2016 GMC Sierra 2500 per the manufacturer. The kit already comes with (2) one inch spacers in the package. You can use up to 1 inch more on the…

view full answer...

Answer 10

For your 5th wheel towing, I recommend the 2008 Chevy 2500 with the 6.6L V8 Duramax which based on the cab and bed length as well as drive axle will have different towing limits. I've listed them below: 2500 Reg Cab Long Bed (LB) 4WD--15,500 2500…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...