Height of Timbren # TTORSEQ and Spacers Needed for Lifted Truck

Question

Question:

I am wanting to know how tall the Timbren is with the bracket installed? I have a 2inch lift in the back and am figuring I will need a spacer or two to get my clearance right with the axle. Thanks!

asked by: Dustin

0

Expert Reply:

I went out to our warehouse and measured an overall height with the mounting bracket of 5 inches for the Timbren Rear Suspension Enhancement System # TTORSEQ. Timbren recommends having a 1/2 inch to 1-1/2 inches between the spring and the axle when the truck is empty so if you measure between the frame where your bump stop is mounted and the axle and get greater than 6-1/2 inches you will want to fill that gap with a spacer or two.

We have 1 inch Spacers with # TA25723-90AD00 or 1/2 inch Spacers # TA25722-90F00 available.

expert reply by: Chris R

0

click to enlarge

Answer 1

For body lifts like what you have Timbrens work just fine as-is without needing type of adapter or spacer. That means the part #TGMRCK25S will fit your 2008 GMC Sierra and work well.

view full answer...

Answer 2

Timbrens would be the way to go since you are hauling quite a bit of weight. So for your 2008 Chevy Silverado 2500 you'd want the part #TGMRCK25S which can give you up to an additional 6,000 lb of suspension support. You should note that this kit…

view full answer...

Answer 3

The GVWR of a vehicle is set in stone. There is nothing you can do to increase the capacity short of replacing the axle, suspension, and other load bearing and drive train components. What suspension enhancement like #TGMRCK25S does is help support…

view full answer...

Answer 4

The suspension enhancement option I recommend for your 2008 Chevy Silverado 2500 is the SumoSprings Rebel Custom Helper Springs #SSR-201-40-2. These are going to do a fantastic job to help control your Chevy when towing your 5th wheel because they…

view full answer...

Answer 5

The Timbren Rear Suspension Enhancement System #TGMRCK25S is a correct fit for your 2005 Chevrolet Silverado 2500 whether it is a 2WD or a 4WD version. This kit will install without need for the included 7/8-inch thick spacers UNLESS the truck has a…

view full answer...

Answer 6

As your 2021 Toyota 4Runner is lifted, you will indeed need to use spacers when installing a Timbren suspension enhancement system. The correct spacers will depend on if you will be using both rear and front jounces, and I have all options for your…

view full answer...

Answer 7

For your 2007 Chevy Silverado 2500HD Classic the Timbren kit you need is the part #TGMRCK25S. Since you have the factory suspension on the truck this kit will fit and work well. I attached an install video for this kit on a 2007 Chevy Silverado…

view full answer...

Answer 8

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Answer 9

Yes, The Timbren Spacer #T68MR will work with The Timbren Suspension Enhancement #TGMRTT35D on your 2016 GMC Sierra 2500 per the manufacturer. The kit already comes with (2) one inch spacers in the package. You can use up to 1 inch more on the…

view full answer...

Answer 10

Using a spacer kit like the #T68MR to allow one side of the truck's suspension to engage sooner will give you more support on that side but since it's hard to say if that will happen to be the sweet spot you are looking for in terms of…

view full answer...

Answer 11

For your 5th wheel towing, I recommend the 2008 Chevy 2500 with the 6.6L V8 Duramax which based on the cab and bed length as well as drive axle will have different towing limits. I've listed them below: 2500 Reg Cab Long Bed (LB) 4WD--15,500 2500…

view full answer...

Answer 12

If you check out the attached review video you will see that at the 2:33 mark he measures one of the bump stops that comes with the Timbren #TTORSEQ and it has an overall height measurement of 3-5/8". This kit is confirmed to fit your 2015…

view full answer...

Height of Timbren # TTORSEQ and Spacers Needed for Lifted Truck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching