Connection Point for Valley Custom Fit Vehicle Trailer Wiring, # 30218 for a 2004 Ford E-150 Van

Question

Question:

t connector 4 the 2004 e150. What wires go wear?

asked by: Jeff

0

Expert Reply:

When installing the Valley Custom Fit Vehicle Wiring, # C56020, for Ford E-series vans, you will just need to plug in the connectors on the wiring harness to the connectors behind each of the tail lights. The bundle with the yellow, brown, and white wires goes to the left (driver side) tail light. The bundle with the green and white wires goes to the right (passenger side) tail light. I have included a link to the installation details for reference.

expert reply by: Michael H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 6

It sounds like you are needing to install a 7-Way connector at the rear of your 2005 Ford E-150. If your Ford Van did not come with the factory tow package (with a 7-way connector), then there will not be a built in socket or harness under the…

view full answer...

Answer 7

I recommend that you do not remove or change the setup of the pn box on your 2006 Grand Junction 5th Wheel Trailer. There may be a reason that the Mor/Ryde pin box needs 10 bolts to mount to the trailer. Removing one bolt may weaken the mount and…

view full answer...

Answer 8

The 4-way install harness part #C56020 that you referenced is a confirmed fit for your 2005 Ford E-150 van and would be one component needed to install your Curt Echo part #C79DR. You would also need the part #C26DR with 10 gauge wire part #10-1-1…

view full answer...

Answer 9

Yes, you can use the Wesbar Adapter item #707250 to connect a 7-Way trailer connector to your Escapes 4-way connector. However, you won't be able to control the brakes or have an accessory line that keeps your battery charged. If you are…

view full answer...

Answer 10

The Furrion Chill Replacement RV Air Conditioner for Dometic Brisk Setup - 15,000 Btu #FR42PV rooftop unit is fixed on the RV roof using 4 long bolts through the mounting frame from the interior of the RV ceiling. So you will need to be able to…

view full answer...

Answer 11

It sounds like you are looking for a spare tire carrier to use on the a-frame portion of your Little Guy Trailer. If that is the case then I do have an option for you but the Folding, Bumper Mounted Tire Carrier part #TR-2 won't work as it is…

view full answer...

Answer 12

If there is no trailer connector on your 2006 ford E-250 van, I recommend the Curt Custom Fit Vehicle Wiring, part #C56020. This is a quick and easy installation on your van. This plugs directly into your existing wiring and requires no cutting or…

view full answer...