What is Amperage Draw of Terra 3500 Superwinch part # SW1135220

Question

Question:

I intend to install the 3500 on a boat trailer, using a separate deep cycle battery installed in a minn kota battery box. The box has a 50 amp breaker. Is this sufficient to use , and is there any wiring diagram available if not using an ignition switch? Would that wire go to the + post on the battery?

asked by: Joe

0

Expert Reply:

The power draw of the Terra 3500 Superwinch part # SW1135220 that you referenced is 19 amps when pulling 0 lbs and 190 amps if pulling it's capacity.

A 50 amp breaker isn't going to be enough.

expert reply by: Jameson C

0

Answer 1

In order to power the Superwinch Terra Series ATV Winch part #SW1135220 located on the rear of your vehicle, I recommend using the Winch Trailer Wiring Kit part #BDW20043. This kit comes with everything you will need to attach the winch to the…

view full answer...

Answer 2

I was able to find a wiring diagram for the Superwinch ATV A3500 winch that you have. I also attached a link to the install instructions for this winch in a separate email.

view full answer...

Answer 3

Most winches have a higher-rated circuit breaker so while I don't know exactly what size you need for your Harbor Freight Badland ZXR 3,500 lb winch, I can say that the Replacement Circuit Breaker for DL StrongArm Winch Wiring Harness #DL304025…

view full answer...

Answer 4

Electric winches can draw a lot of power so it would be best if they had a dedicated power source. There are several ways to wire up a trailer and I have included a how-to article for you to review to determine which method is best for you. Since you…

view full answer...

Answer 5

For a winch like the Superwinch S6000 Winch #CU854754 you will simply want to use the Trailer and Vehicle Electric Winch Wiring Kit #BDW20207. Since winches can vary on how much they can pull this also affects how much power they need. For a winch…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

The Class V hitch we have for your 2004 Dodge Ram 2500 with the best ground clearance is the Curt hitch part #C15809. It doesn't tuck right under the rear bumper like what you can see in the attached picture but it does sit the highest.

view full answer...

What is Amperage Draw of Terra 3500 Superwinch part # SW1135220

Product Page this Question was Asked From

Continue Researching