Comparing the Stromberg Carlson # LG-3 and the Lippert Components # LC333964 Landing Gear Sets
Question:
I have a 2007 Dutchman 30foot with wheel RV trailer model #30CE-2S. I would like to replace the original landing system by using the current landing leg clamps without having to weld in a new setleg = 29-1/2inch long and the distance between the clamps is 17-1/2. Based on research at your site it indicates that the 6500# Stromberg Carlson LG-3 and the 6000# Lippert LC 333964 should be direct replacements for the existing system. Am I correct or should I consider purchasing other components?
asked by: Robert V
Expert Reply:
You are correct in your findings. Both sets of Landing Gear, the Stromberg Carlson # LG-3 and the Lippert # LC333964, have the standard weld stop locations where the inside to inside measurement is 15-1/2 inches and the outside to outside of the weld stop measurement is 17-1/2 inches and they measure 29-1/2 inches tall.
Either of these will fit the current brackets you have on your RV. One other thing you might want to note is that part # LG-3 has a total lift of 34-7/8 inches with travel being 19-7/8 inches and the drop leg being 15 inches. The part # LC333964 has a total lift of 37 inches with the travel being 21 inches and the drop leg being 16 inches. This will not affect how they fit on your RV, just how much lift they offer.
Products Referenced in This Question
Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 37 Inch Lift
- Weld-On
- 2 Jacks
- Lippert
more information >
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 6001 - 7000 lbs
- Electric Jack
- Landing Gear
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: landing gear
- Shop: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Video: Stromberg Carlson Electric Landing Gear Set Review
- Video: Lippert Electric Landing Gear Set Review
- Shop: Fifth Wheel Hitch
- Q&A: Replacement Landing Gear for 2014 Heartland Gateway
- Shop: Drop Leg for Lippert Power Jack - 8-11/16" Tall - 9" Diameter Footplate - Zinc
- Shop: Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin
- Shop: Spring-Loaded Pull Pins for Stromberg Carlson Landing Gear - Qty 2
- Shop: Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: RV Jack Pads
- Shop: Blind Spot Detection
- Q&A: Choosing the Correct Landing Gear for a 2009 Sandpiper Trailer
- Search Results: landing gear parts
- Search Results: electric landing gear
- Search Results: landing gear pad
- Search Results: 5th wheel landing gear
- Search Results: landing gear pins
- Search Results: lc405217
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Lippert Landing Gear Recommendation for a 2013 Cougar Fifth Wheel Trailer 244RL
- Q&A: Replacement Landing Gear for Keystone Montana 34RL
- Q&A: How to Determine Correct Replacement Landing Gear
- Video: Bulldog Camper Jack - Landing Gear - BD500162 Review
- Q&A: How Do You Determine What Landing Gear Is On Your Trailer?
- Q&A: How to Determine Correct Replacement Landing Gear For 5th Wheel
- Video: Stromberg Carlson Electric Landing Gear Set Review LG-1
- Shop: Cold Air Intake
on Trailer Jack
