Replacement Landing Gear for Keystone Montana 34RL

Question

Question:

We have a 34RL Montana. It has the lippert landing gear which we need to replace. Is your system compatible with the Lippert#333964 universal mount power landing kit.

asked by: Pam

0

Expert Reply:

We do have the Lippert landing gear for your Montana but # LC333964 is not the correct part.

The Montana line has specific legs designed for it. You'll need # LC178653 for the lead leg and # LC178652 for the follow leg.

expert reply by: Charles S

0

Answer 1

To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there…

view full answer...

Answer 2

The Lippert Landing Gear part #LC333964 will fit your fifth wheel trailer. At worst you would need to find a qualified welder to move the brackets on your trailer so that they will match up with the landing gear set. If the distance from outside to…

view full answer...

Answer 3

The square tube on the Ultra-Fab Deluxe Electric Landing Gear Set, #UF17-943010, measures 2-1/2 inches x 2-1/2 inches and it measures 24-1/4 inches tall. The foot plate measures 8 inches long x 5-3/4 inches wide. I have attached a photo showing…

view full answer...

Answer 4

The Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 referenced in your question is a great landing gear system that features dual electric jacks that will raise and lower at just the flip of a switch. The jacks themselves can operate…

view full answer...

Answer 5

You are correct in your findings. Both sets of Landing Gear, the Stromberg Carlson #LG-3 and the Lippert #LC333964, have the standard weld stop locations where the inside to inside measurement is 15-1/2 inches and the outside to outside of the weld…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 8

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 9

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 10

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Replacement Landing Gear for Keystone Montana 34RL

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching