Highest Capacity Bolt-On RV Hitch for National Class A Motorhome on Workhorse W-22 Chassis

Question

Question:

Whats the highest rated tow hitch that will bolt on to my w-22 workhorse chassis? 2006 national sea breeze.

asked by: Don M

0

Expert Reply:

The highest-rated 2-inch RV hitch we offer that can be bolted on to an RV frame is Curt # C13702. This hitch is rated for 500-lbs tongue weight (or 600-lbs if used with weight distribution) and it will fit RV frames from 18- to 51-inches in width.

Similar hitch # C13701 offers the same fit and capacities but its receiver tube is lower, 2-inches of drop for better clearance around the RV's rear exterior panels.

These and other RV hitches, some of which fit wider frames, are shown on the linked page.

expert reply by: Adam R

0

Answer 1

Workhorse is not affiliated with Ford though they were at one time related to GM and are now part of AMP. Regardless of who controls the Workhorse chassis division there are only universal type trailer hitches for them but no custom ones. The most…

view full answer...

Answer 2

Since there is not a custom fit trailer hitch receiver available for our 2003 Winnebago Ultimate Advantage built on the Spartan Chassis I recommend having a local fabricator install the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 9

We do have a couple Class V hitch options available for your 2020 F53 and I have 3 options listed below. These will all be rated to 16,000 pounds towing and 1,600 pounds of tongue weight and use a 2" receiver opening. They will all also fit a…

view full answer...

Answer 10

The trailer hitches we have available for the 2014 GMC Savana Van are designed to fit the full size van model. To see if these will fit your Cutaway version, I just recommend taking a couple measurements on the vehicle's frame. The trailer hitch…

view full answer...

Answer 11

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body…

view full answer...

Highest Capacity Bolt-On RV Hitch for National Class A Motorhome on Workhorse W-22 Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching