Vent Cover for the Kitchen Area on a 2001 Jayco Eagle

Question

Question:

We need to replace the vent covers on the roof over the kitchen area, not the air vents in the bathroom, couch area and bedroom. Do you know the part numbers for a 2001 Jayco 304bh?

asked by: Diane

0

Expert Reply:

Since we do not have the specs for specific trailers I do not know exactly what vent roof that you need.

With that being said, we do have a selection of roof vents that I have linked for you to look through. You can narrow the search by selecting the correct dimensions of your current vent. If you would like a recommendation for a roof vent all I will need are the dimensions. One of the most common sizes is 14 inches x 14 inches roof vents. A cover like the MaxxAir II # MA76JR would be a great option if your roof vent is 14 inches x 14 inches.

expert reply by: Jon G

0

Answer 1

Yes, if you check out the picture of the underside of the MaxxAir II RV and Enclosed Trailer Roof Vent Cover #MA76JR that I attached you will see the screen that is on the inside of the cover that would prevent bugs from entering.

view full answer...

Answer 2

You will want the Replacement Weather Seal for Ventline E-Z Lift Ventadome Trailer Roof Vents - 51" Long #BVE0127-00 or #BVD0455-01. This has the groove on one side and the compressed O weather seal on the other. I've attached a video to…

view full answer...

Answer 3

The MaxxAir II RV and Trailer Roof Vent Cover part #MA76JR is a translucent white color.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 12

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...