Type of Fastener for Installing Snap-Loc E-Track Tie-Down Anchor SLSS

Question

Question:

Good morning, Im thinking of buying the snaploc single etracks. My question is what type of self drilling screw do I use ? I notice I cant use nut and bolt with Washer on the side of tail gate. Thanks

asked by: Oscar

0

Expert Reply:

The Snap-Loc E-Track Tie-Down Anchor # SLSS can be attached to the desired mounting surface with the type of hardware is appropriate for that material. If you are mounting these to wooden surface use fasteners for wood, e.g. wood screws. For a metal surface use fasteners made for metal, e.g. self-tapping sheet metal screws. We also offer carriage bolt hardware # SLHCBDS-P.

Keep in mind that the actual weight capacity of each tie down will depend on the strength of the surface you mount it to and that of the hardware used.

expert reply by: Adam R

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 4

With plywood walls that are as thin as yours, it's possible that they may not support what you are looking to do. The only way you will be able to utilize the Erickson Horizontal E-Track #EM59150 (2 feet) or #E19148 (5 feet) is by installing it…

view full answer...

Answer 5

Since the slot dimensions and capacity of different brands of E-Track are identical, really the only differences are the finish and the lengths the tracks are sold in. If you're using the E-Track in an area where aesthetics are important, you can…

view full answer...

Answer 6

On an 4 foot long section of E-track #EM19147 and 2 screws every 16 inches that is a total of 6 screws in the aluminum frame. This most likely will not get you near the capacity of the E-track. I recommend bolting through the aluminum frame so that…

view full answer...

Answer 7

Your plan of having an e-track like the part #E19148 attached to two different floor boards in your trailer would be perfect. This will distribute any weight on the e-track to two boards which is a sturdier way to go about it.

view full answer...

Answer 8

Yes, you can drill holes to add an A-frame jack to your pop-up camper if your current jack is getting in the way of your anti-sway bars. You will need to have a mounting plate to of some sort to drill into as opposed to drilling into the frame of…

view full answer...

Answer 9

Backing plates, like the etrailer Backing Plate #e96RR, are always a good idea. Using bolts and backing plates will provide a more secure installation of the Erickson E-Track. You will want to use 4 bolts per backing plate. If you do decide to use…

view full answer...

Answer 10

We do recommend backing plates for all e-track installations. They will provide additional support. You will need a set of four backing plates, part #e66RR, for an 8' section of E-Track. I have included a product description link, a weblink on…

view full answer...

Answer 11

When securing your motorcycle inside your enclosed 12 foot long trailer using a chock like the Tow-Rax #TWSPWM the most important factor to consider is the trailer's tongue weight. You will just want to make sure that its tongue weight with the…

view full answer...

Type of Fastener for Installing Snap-Loc E-Track Tie-Down Anchor SLSS

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching