Does Curt Hitch # C92UR Fit 2017 Honda Civic Hatchback

Question

Question:

Can you double check this indeed works on Civic Hatchback 5 door? Does anything change on the install? Do you not need to grind off part of the bumper metal, or do you still have to do that?

asked by: Hans

0

Expert Reply:

We confirmed with Curt that the hitch part # C92URthat you referenced is a confirmed fit for your 2017 Honda Civic hatchback. There is fascia trimming required as well as some bumper beam trimming as well. I attached an install video that shows this along with the installation instructions for you.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite trailer hitch #24942 for your 2018 Acura TLX has a 1-1/4 inch receiver. This is a Class I hitch so a bike rack will need to be Class I rated. Looking at the 1Up Quick Rack they state it fits 1-1/4 inch and 2 inch receivers but they do…

view full answer...

Answer 2

Even though it is not a fit for it, it is not impossible to install the #C92UR Trailer Hitch Receiver on a 2019 Honda Civic Si. However, in order to do this, you will need to remove the center mounted exhaust pipe. I have attached a few photos for…

view full answer...

Answer 3

While none of the custom trailer hitches are able to fit directly to your 2017 Honda Civic Hatchback with the center exhaust, if you check out the attached photo sent in by a customer you can see that they were able to get the 1-1/4" Curt…

view full answer...

Answer 4

Yes, the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4", part #C92UR, that fit the 2021 Honda Civic without the center exhaust will also fit your 2022 Honda Civic. The installation will be the same for both vehicles. I have included…

view full answer...

Answer 5

The Curt hitch part #C92UR that you referenced does fit your 2024 Honda Civic Sport Touring. Basically this hitch fits all models except ones with center exhaust.

view full answer...

Answer 6

For your 2017 Honda Civic you will have no problem using a Rhino-Rack roof rack with a Yakima Skybox NX like #Y95AV. Roof boxes and roof racks are compatible between manufacturers, and you won't have crossbar spacing issues. For a specific fit on…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...