Exterior or not?

Question

Question:

The description is a bit confusing. Title states INTERIOR, description states use as a porch light on a covered porch. Well there is no such thing as a covered porch on a travel trailer that travels on the Interstate.... Can I use this on the exterior of my trailer or not? Thanks for your input.

asked by: Tory C

0

Expert Reply:

It's technically an interior light so I wouldn't recommend you use it on the exterior of a trailer even though it would most likely be fine.

expert reply by: Jameson C

0

Answer 1

If you grab light #ILL70CBSBAWN and hold the base with one hand you can pivot the light part up, almost like it is hinged. The gasket has an adhesive on it that makes it seem like the 2 parts are all one piece but they aren't. I tested this out…

view full answer...

Answer 2

The Optronics Opti-Brite RV Interior Strip Light #ILL70CBSBAWN referenced in your question is without a doubt, a very cool light assembly that would look great on an RV porch. While this unit is not necessarily designed as an outdoor light, it does…

view full answer...

Answer 3

The first thing to check on the Opti-Brite RV Interior Strip Light w/ Switch - Awning Mount - White LEDs - Black Housing Item #ILL70CBSBAWN is the ground wire. Make sure it is grounded to a clean bare metal surface. A weak ground could cause the…

view full answer...

Answer 4

I recommend installing the Opti-Brite LED Strip Light for RV Awnings #OPT32ER under your awning so you can use it whether your awning is out or in. Since this is a small LED light you should be okay tying into the wiring for the roller lights but…

view full answer...

Answer 5

While the Optronics Opti-Brite RV Interior Strip Light w/ Switch #ILL70CBSBAWN referenced in your question has a sealed, waterproof construction, it is designed primarily for interior use or as a porch light on a covered porch. It is not necessarily…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Exterior or not?

Product Page this Question was Asked From

Continue Researching