Fifth Wheel Trailer Hitch Installation Bracket Kit for 2007 Chevrolet Classic 2500 with 8 Foot Bed

Question

Question:

Will this pt# fit 2007 chevy 2500 long bed classic

asked by: Scott

0

Expert Reply:

Yes, the Curt Fifth Wheel Bracket Kit # C16418 will fit your 2007 Chevrolet Silverado Classic long bed.

If you also need the base rails use # C16418-204.

expert reply by: Charles S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Fifth Wheel Trailer Hitch Installation Bracket Kit for 2007 Chevrolet Classic 2500 with 8 Foot Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching