Type of Grease Used for the Bulldog Side Wind Jack Assembly

Question

Question:

What type of grease is used in your Bulldog trailer jacks?

asked by: Taylor R

0

Expert Reply:

There isn't necessarily any specific grease to use in the Bulldog Side Wind Jack Assembly # BD182700. You can use the LubriMatic Disc/Drum Brake and Wheel Bearing Grease # L11465 along with the LubriMatic Professional Pistol Grease Gun # L30416.

You can find a typical grease and grease gun at your local hardware store as well.

expert reply by: Jon G

0

Answer 1

We spoke with our contact at Fulton and he said the Fulton Jack, #FXPD15L, can be lubricated with any general-purpose grease like our LubriMatic Lithium Grease, #L11316. You can remove the cap at the top of the jack and put the grease in the cap.…

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

The highest quality grease we carry for wheel bearing is the LMX red grease like the part #L11390 that you referenced. LMX Red is heavy-duty, premium grease for the toughest lubricating jobs on the biggest, heaviest equipment. It performs better…

view full answer...

Answer 4

I have a solution for you, but I don't recommend using white lithium grease on your wheel bearings, since it's more of a general lubricant and there are much better products specifically designed for wheel bearings. Instead, I…

view full answer...

Answer 5

The etraielr Round A-Frame Jack part #TJA-5000S-B is not very picky when it comes to the grease type so you could use a high-temp wheel bearing grease like the LubriMatic LMX Industrial Strength Grease part #L11390 without issue. The manual for the…

view full answer...

Answer 6

The Bulldog Square Jack part #BD182500 has a removeable end cap on the top that you will remove and reinstall to service the jack, therefore it's not a sealed jack. The type of lubrication used is just a standard automotive grease per Bulldog. We…

view full answer...

Answer 7

I am not totally sure which jack you are referencing but most jacks are designed to be lubricated with white lithium grease like part #L11354.

view full answer...

Answer 8

We have exactly what you would need. For the right hand side you would want part #23-181, for the left hand side part #23-180. I attached an install video for you to check out as well.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 12

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...