Bearing Kit For SureTrac Trailer With #84 Spindles

Question

Question:

Hi, I have a 00 SureTrac trailer 10x5 single axle, and I need to replace my bearings. SureTrac says the inner is a 68149 and outer is a 44649, hub seal is 1019. Do you have a set of these including cotter pins or do you have a kit that I can go off of?

asked by: Don L

0

Expert Reply:

We do have a kit for you. You will want Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100. You may want a bearing packer like # PTW1218 and an installation set like # PTW83020.

expert reply by: Jason S

0

Answer 1

I was able to do some digging and found out that Sure-Trac trailers use either a Dexter or Lippert axle, and both of these 3,500 lb axles use the same bearings and grease seal, so we have exactly what you need. The Bearing Kit for #84 Spindle…

view full answer...

Answer 2

Yes, the 7-Piece Installation Set for Bearings, Races, and Seals #PTW83020 is compatible to use with Bearing #L44649.

view full answer...

Answer 3

I reached out to EZ Loader who provided me with the part numbers you are needing. Inner Bearing #L68149 Inner Race #L68111 Outer Bearing #L44649 Outer Race #L44610 Grease Seal #168255TB The 7-Piece Installation Set #PTW83020 and Seal Puller…

view full answer...

Answer 4

The coupler should be very difficult to push in by hand but it doesn't return on its own. There is likely a problem inside your coupler that will need to be addressed to get it working properly again. It is most likely the shock that is inside.…

view full answer...

Answer 5

With surge brakes, you have a brake actuator applying the needed pressure to the brakes but to be able to back up you will need to have a manual lockout or an electric lockout solenoid, like #T4748800, which will close when you shift the vehicle into…

view full answer...

Answer 6

Sounds like you made the easy mistake of putting too much grease in your hubs with your Bearing Buddies and it blew out your seal and emptied the grease out and damaged the bearings and that's why the wheels are locked up. So you'll need to…

view full answer...

Answer 7

The correct torque for installing lug nuts on your 5 X 8 trailer's 5-lug wheels will depend on the size of the lugs. For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs. For a 9/16-inch lug the torque spec ranges from 135- to…

view full answer...

Answer 8

For a 10 inch hub drum with a 6 on 5-1/2 inch bolt pattern that will fit your Lippert 3,500 lb axles the Dexter part #84656UC3-EZ will be what you would need. I also attached a link to a page that has all of the 16 inch trailer wheels and tires we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Bearing Kit For SureTrac Trailer With #84 Spindles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching