Recommended Keyed-Alike Locks for Multiple Trailer Hitches

Question

Question:

Hello, As I have multiple trailer hitches- standard ball, bulldog type, and even gooseneck ball-eventually. as well as multiple tow vehicles, I am looking for items that could be keyed alike- for hitch pins, hitch locks and even gooseneck hitches. Not those ABUS keys, unless you can get more than 2 at a time, you cant find those anywhere short of a locksmith if they even have them. Is there anything like this available. Getting too many darn keys, Thanks

asked by: Steve M

1

Helpful Expert Reply:

I do have a few possible solutions for you, however we do not currently offer a product that would allow you to have everything in your system keyed-alike.

Depending on the tow vehicles you drive, I recommend looking at the BOLT Trailer Hitch Receiver Locks like the # BL7023584. These are vehicle specific pin locks that, depending on the tow vehicle you are using, can actually be coded to your ignition key - so you will always have the correct key with you. Since you do have multiple tow vehicles, you would need to find a compatible lock for each vehicle, but you would not need to worry about bringing the corresponding key for the hitch lock. I have included a link that takes you to our selection of this product, so you can hopefully find the correct hitch receiver locks that are compatible with your tow vehicles.

For a standard trailer hitch receiver lock that can be keyed-alike, I recommend the etrailer # e98882 for 2 inch receivers. This is a stainless steel lock that fits 2 inch trailer hitches. You can just select "keyed-alike" in the drop-down menu on the product page when ordering.

Lastly, I have included a link that takes you to our complete selection of keyed-alike products for you to look into this further.

expert reply by: Chris R

1

Answer 1

Yes, the EZ Lock Gooseneck Coupler Lock Combo #BLTL-53-40D2 that you referenced comes with two locks and would work well on your 20k Bulldog Coupler. One lock secures the coupler opening and the other secures the inner tube of the trailer to the…

view full answer...

Answer 2

Yes, the EZ Lock Gooseneck Coupler Lock Combo part #BLTL-53-40D2 will work with a Bulldog gooseneck coupler. I have attached a photo of the above lock installed on a Bulldog gooseneck coupler for you as well. The EZ Lock Gooseneck Coupler Lock Combo…

view full answer...

Answer 3

The BOLT Trailer Hitch Receiver Locks like the #BL7018446 can only be keyed to one key. Once you set it to a key it can't ever be changed. The one you'd need for a 2010 Toyota Highlander is the part #BL7023584. If you sold your Highlander…

view full answer...

Answer 4

The harness difference you found is because the control unit you should have ordered looks to be the #LC379604 which fits the newer versions of the step. Most likely the steps of your RV were replaced with a kit made after 2005.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...