Can Fulton Jack FXP10 Attach to 2x4 inch Trailer Frame

Question

Question:

Will this fit my 2x4 in trailer

asked by: Tom

0

Expert Reply:

Your trailer frame might be a bit too thin for the Fulton jack part # FXP10 to fit directly, but what you can do is use a metal spacer to make the frame a bit thicker so that the jack can attach to it. Or you can use the weld on bracket part # P9012-00 which will replace the bolt on bracket and allow you to attach the jack directly to the trailer.

expert reply by: Jameson C

0

Answer 1

Just click on the linked page to see all of our LED-type red oval trailer stop/turn/tail lights like #STL22RB from Optronics. This particular light measures 6-1/2- x 2-5/16-inches and uses a mounting grommet #A70GB and bracket #BK70BB. LED lighting…

view full answer...

Answer 2

The Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Red Lens #STL78RB is a single light. If you want a set, you will need to change the quantity box on the product page when ordering. I've attached a photo of…

view full answer...

Answer 3

The Snap-on Reflector Ring #A78RXB that you referenced attaches at the top, bottom, left, and right of the mounting flange of the light assembly with clips that slip over the flange when pressed on. To remove the ring you basically would want to grab…

view full answer...

Answer 4

I may have a solution for you, however, the Optronics Sealed 6-1/2 Inch LED Trailer Light, #STL70RB, does not contain reflectors. At this time we do not have any 6-1/2 inch oval tail lights that have reflectors in the lens. Instead, I would recommend…

view full answer...

Answer 5

My recommendation for your application is the Sealed, 6-1/2" Oval LED part #STL78RB. I attached a review video for you to check out as well. Then you can use the Snap-on Reflector Ring for STL78RB Series LED Lights - Red #A78RXB. This will allow…

view full answer...

Answer 6

The GloLight LED Trailer Tail Light #STL178RB will not work with the Snap-on Reflector Ring for STL78RB Series LED Lights #A78RXB as it will not fit the light. If you wanted to use that reflector ring you would need the Optronics LED Trailer Tail…

view full answer...

Answer 7

Although the Snap-on Reflector Ring, #A78RXB, will not fit the STL178 series lights like the Optronics GLOLight LED Stop/Turn/Tail Light #STL178RFPB, I do have a solution for you. Take a look at the Sealed, 6-1/2" Oval LED Trailer Stop, Turn and…

view full answer...

Answer 8

The older generations of the Wesbar submersible low-profile lights came with sealed light bulb capsules that are not replaceable like what you have in the picture you uploaded. Your best option is to replace the lights with new lights like part…

view full answer...

Answer 9

Trailer axles are designed to have the bow in them that you described. This allows the axle to flatten out when it is loaded and have the proper camber. If you have axles that are rated for considerably more than what the trailer will ever have…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...