Recommended Brake Controller And Wiring For 2012 Ford E-350 Van
Question:
2012 Ford E350 box van. Need brake control box and wiring for 7 way hook up. I think the # is 90885-3034P and the wire harness with 7 way is ETBT7. Is this correct. Is there anything else necessary? Thanks
asked by: Joe B
Expert Reply:
If you have a factory 4-way trailer connector at the rear of your E-350 Van you can use the Prodigy P2 brake controller and plug-in adapter, # 90885 and # 3034-P. I have attached a photo that shows where you can plug the adapter into behind the dash.
You will then need part # 37185 to give you a working 7-way. You will need to run the brake wire from the brake controller to the plug using part # 10-1-1.
If you do not have a trailer connector on your van you will first need a 4-way trailer connector like part # 118551. You will then need part # ETBC7 to complete the installation. Since you will not have the plug-in harness under your dash you will not need the # 3034-P adapter. You will need to hardwire the brake controller as shown in the attached drawing.
When working with electrical connectors I recommend using dielectric grease like part # 11755. This keeps dirt and moisture out of the electrical connections and helps prevent corrosion.
I have also attached links to a couple of helpful articles that you can check out.
Products Referenced in This Question
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: How Is Spring Bar Tension Set Up with Trailer Weight Distribution System