Are Oil bath Hubs a Better Option for My 7,000 Lbs Axles Than Using Grease Hubs
Question:
So...I inherited a HUGE headache at work. We regularly pull 16,100 including trailer on 14k axles... Believe me, Im trying to convince management to upgrade to a triple axle! Aside from not keeping up on greasing axles and adjusting brakes when I was hired hell the brake controller had loose wires, I blew up a bearing. I replaced it with the stock EZ lube hub, but now Im wondering if I could have replaced it with an oil bath hub threaded Im reading??!? Ive had a couple seal blowouts on this PIA trailer as Im forced to grease it so often due to overload and we put a lot of miles on it. Whats the general opinion of oil bath obviously semis run them so cant be all gimmick. Im not totally impressed with plastic that could be bumped, cracked, and there goes my lubricant its a dump trailer so regularly getting tracks within inches of hubs. How do you change the fluid and whats the interval? Initial impression it looks like this is an option I should shop for on a new trailer and/or swap out hubs on the old trailer as they fail. Thanks in advance and I use your references/info pretty regularly!
asked by: Mitch O
Expert Reply:
The main reason people like oil bath hubs over grease hubs is the oil bath hubs have a less involved maintenance schedule than grease hubs.
It is recommended to inspect and repack grease wheel bearings and seals every 12k miles. With oil bath hubs, Dexter recommends to periodically check and refill when necessary. It is also recommended to use a high quality hypoid gear oil in SAE 90, 80W-90 or 75W-90 weights. However, periodic inspection of you wheel bearings should not be abandoned because of the switch to oil bath hubs.
For your application., you will need to replace the whole drum and hub assembly to change over to oil bath lubrication. For 7,000 lbs axles, we have two different hub and drum assemblies that will use an oil bath lubricant. Dexter Trailer Hub and Drum with 8 on 6-1/2 Bolt Pattern, # 8-219-9UC3-A and the Dexter Trailer and Hub # 8-219-9UC3. To figure out which hub and drum might work on your axles, you will want to find measurements on the spindles of your axles. There are differences in the size of oil seal between the two hubs. I have attached a picture that will show you the what measurements are needed to pick the correct hubs.
The new hubs use a clear plastic cap nut to help see the oil level in the hubs. Unfortunately, the plastic caps are the only oil caps that are available. However these caps are sturdy and have been the industry standard for use in trailer, commercial, and agricultural applications for many years.
Products Referenced in This Question
Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - Oil Bath
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Oil Bath
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Dexter Trailer Hub and Drum Assembly - 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - Oil Bath
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Oil Bath
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Karrier ST225/75R15 Radial Trailer Tire - Load Range D
- Trailer Tires and Wheels
- Tire Only
- Radial Tire
- Load Range D
- 225/75-15
- 15 Inch
- M - 81 mph
- Kenda
more information >
Continue Researching
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Video: Review of Castle Rock Trailer Tires and Wheels - Tire with Wheel - LH74VR
- Shop: Hydrastar Electric-Hydraulic Actuator w/ Line Kit for Disc Brakes - 1,600 psi
- Shop: Castle Rock ST205/75R14 Radial Tire w/ 14" Margay Aluminum Wheel - 5 on 4-1/2 - LR C - Black
- Shop: Westlake ST205/75R14 Radial Tire w 14" Margay Aluminum Wheel - 5 on 4-1/2 - LR D - Black
- Shop: Hydrastar Electric Over Hydraulic Actuator Kit for Disc Brakes - 1,600 psi
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Triple Axle Trailers - 9/16" Studs - 8 on 6-1/2 - 7K
- Shop: Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs - 30" Lift - 6,000 lbs
- Shop: Grease Seals 10-36 (pair)
- Search Results: hydraulic brake line kit
- Video: Review of Dexter Axle Trailer Leaf Spring Suspension - 7 Leaf Double Eye 8000 lbs Axle - DX74XR
- Q&A: Disc Brake Kit Recommendation for Lippert 7k Axles
- Search Results: oil bath hubs
- Search Results: disc brake line kit
- Search Results: walking beam
- Video: Taskmaster Tires and Wheels CXF105B Review
- Search Results: 490 center cap
- Video: Review of DeeMaxx 220 Inch Long Rubber Hydraulic Brake Hose - DE46GR
- Video: Kodiak Trailer Brakes 18SI-BLKIT Review
- Video: Review of DeeMaxx 16 Inch Long Rubber Hydraulic Brake Hose - DE36GR
- Search Results: 3 16 brake hose
- Search Results: brake fittings
- Video: Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-219-9UC3-A Review
- Q&A: How to Determine Correct Replacement Grease Seal for 44251
- Q&A: Parts to Convert 2017 Grand Design Momentum 376TH to Electric Over Hydraulic Disc Brake
- Q&A: How to Grease a Dexter EZ Lube Axle
- Q&A: Grease to Oil Bath Trailer Hub Conversion Kit for 3500 Pound Axles
- Q&A: Comparing Benefits of Greased Hubs vs Oil Bath Hubs
- Q&A: What Makes 5200lb and 6000lb Dexter Axles Different Capacity?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)