Most Common Trailer Brake Line Fitting Size

Question

Question:

I need a brake hose for my boat trailer. tracker boat, trail star trailer, manufactuer- Fabrique par, tracker marine. ser. 4TM14UG244B001006 YEAR 2003 HELP IF YOU CAN THANKS

asked by: Mike

0

Expert Reply:

How long of a line do you need? Do you know what size you need? The most common size is 3/16 inch like part # BH-3MFS-4-5 which is 54 inches long.

expert reply by: Jameson C

0

Answer 1

The correct Kodiak Disc Brake Kit for a 5,200 lb axle is part #K2R526S for stainless or part #K2R526D for dacroment. In regards to compatibility, the brake mounting flange and spindle size are the only factors we can confirm. I don't foresee…

view full answer...

Answer 2

The item you selected, Titan Disc Brake Kit and Leverlock Actuator w/ Electric Lockout, part #T4747200, is zinc coated to prevent corrosion. To prevent warping, I would recommend allowing the brakes to cool after driving a long distance before…

view full answer...

Answer 3

The majority of our brake line fittings are made from brass which are a bit different than the steel brake line fittings you might be familiar with on a passenger vehicle. Generally speaking, the cause of these brass brake line fittings leaking is…

view full answer...

Answer 4

There are several brake lines in varying lengths and sizes between your disc brake assembly and the surge brake coupler on your trailer. I am not sure which one you are looking for but if you can pinpoint this for me I may have some better advice for…

view full answer...

Answer 5

The choice of oil bath or regular hubs is up to the manufacturer. They are usually found on higher capacity axles, though as you know there are some on lower capacity axles. You can convert some hubs from grease to oil bath using a kit such as…

view full answer...

Answer 6

Normally trailer brake lines are only used on trailers. However, if your vehicle has brake line fittings that match what the part #18TA-BLKIT has and the psi of the system does not exceed 1,600 psi this line could work for you as these are SAE…

view full answer...

Answer 7

I have added a link to a help article on everything you need to replace (or add) hydraulic drum brakes, but let's start with the actuator. What you need to know is the weight capacity you need, the hitch ball size you are coupling to, and the…

view full answer...

Answer 8

Thank you for the photo! Since your current drum brake assembly is part 023-342-00 from Dexter Axle the replacement brake kit for both sides of your axles is part #23-342-343. You will need one kit for each axle on your trailer. These are free…

view full answer...

Answer 9

Sounds like you are trying to install the wrong brake line to the Kodiak Disc Brake Caliper #KDBC225S that you mentioned. The fitting size needs to be 3/16 inch like what comes with the #18TA-BLKIT. Since I don't know what brake lines you have…

view full answer...

Answer 10

I do have an option for you but the coupler on your trailer is very old and we simply don't carry parts for them anymore as they were discontinued by the manufacturer. Therefore, the only option we can offer is a new coupler, the Demco Hydraulic…

view full answer...

Answer 11

The Tekonsha Prodigy P3 Trailer Brake Controller #90195 along with the wiring harness #3063-P is all that is needed to add your controller to your Sprinter with Factory Trailer Plug. Since you are not getting power, you should check fuse F55 which is…

view full answer...

Answer 12

The first thing you'll want to do is determine the capacity of your axle. This can usually be figured out by the getting as much of the following information as possible: Wheel bolt pattern (#of lugs and bolt circle diameter, see help article)…

view full answer...

Most Common Trailer Brake Line Fitting Size

Product Page this Question was Asked From

Continue Researching