Brake Controller Wiring Harness for a 2016 Thor Windsport 35C Class A RV on Ford F-53 Chassis

Question

Question:

I have a 2016 Thor motorcoach wind sport 35c . Ford V-10 RV and I need the OEM wiring harness plug for a brake controller . Need to know which is the right adapter plug. Thank you !

asked by: Jim

0

Expert Reply:

I believe your 2016 Thor Windsport 35C was built on the Ford F-53 chassis meaning it will using wiring harness # 3035-P for a brake controller. The factory plug should be located near the emergency brake pedal.

expert reply by: Michael H

0

click to enlarge

Answer 1

The brake controller connector is located on the left side of the steering column support, as shown in the provided photo. You'll need the #3035-P brake controller wiring harness.

view full answer...

Answer 2

The exact replacement foot plate for the Level Up system you have is not available as a replacement. But you could use #LC314667. The issue is that it uses a smaller bolt than the Level Up foot. So you would have to use a 1/2 inch bolt that will…

view full answer...

Answer 3

You will need to confirm this for your rig, but it looks like many 2016 Forest River FR3 motorhomes do use the Lippert Components Hydraulic Ground Control Leveling System. It's not possible for us to know what system is on your motorhome but…

view full answer...

Answer 4

I suggest using a strap wrench to hold the cylinder side while tightening the installation hardware on the Replacement Foot Pad, #LC324269.

view full answer...

Answer 5

The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 #LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube…

view full answer...

Answer 6

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 7

Since you already have a factory 4-way flat on your 1996 Ford F-350 you will need the Adapter 4-Pole to 7-Pole #37185. This will plug into your factory 4-way and the rest of the wiring will have to be spliced into your factory wiring as I do not see…

view full answer...

Answer 8

Hey John, I can definitely help with that. The Reese brakeman controllers are compatible with the Tekonsha brand plug-and-play adapters. For your 2002 Ford E250 you can use the #3035-P to plug directly in to the factory brake controller plug. You…

view full answer...

Answer 9

The trailer wiring harness for your 2014 Ford Explorer is actually quite easy to install. Take a look at the picture I've attached. There are two connectors at the rear on the passenger's side. The wiring harnesses we carry, like part #118540…

view full answer...

Answer 10

The 4-way trailer connector wiring harness I recommend for your 2008 Ford Econoline E-350 Van is the part you reference, part #118551. This custom wiring harness adds a 4-way flat trailer connector at the back of your Ford Van to power your…

view full answer...

Answer 11

Your 2014 Fleetwood Bounder should be on a Ford F-53 chassis. If you found the gray plug next to the brake release (see attached photo) then this means that you should just be able to use a plug-in adapter to easily install your brake controller. Out…

view full answer...

Answer 12

On the 2014 Ford F-53 chassis the brake controller port is located on the left hand side of one of the steering column supports. The plug is gray in color, and you should be able to see it if you look to the right of the emergency brake release…

view full answer...

Brake Controller Wiring Harness for a 2016 Thor Windsport 35C Class A RV on Ford F-53 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching