Grille Guard and Front Hitch that Fits 2016 Ford F-150

Question

Question:

Is there a front hitch that can be installed that is compatible with an existing westin grill guard

asked by: Jonathan H

0

Expert Reply:

We have found that with the Westin HDX Grille Guard part # 57-3835 you can fit the Draw Tite front hitch part # 65067.

I attached a picture that shows the two fitting together just fine.

Normally front hitches and grille guards can't fit together at the same time but this vehicle/setup happens to be an exception.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Undercover offers several types of hard tonneau covers for vehicles like your 2010 Nissan Frontier so you'll want to make certain that your particular cover series/model can handle the weight of the load you intend to place on the rack you…

view full answer...

Answer 2

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 3

Hey Bob, Roof rack systems are typically only rated up to 165lbs because that's typically above the capacity of the vehicle's roof. More recently all manufacturers are switching to removing the capacity from the listing and telling…

view full answer...

Answer 4

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 5

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 6

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 7

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 8

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 9

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 10

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Answer 11

For your 2024 GMC Sierra 3500 we only have the Curt front hitch part #C52NR as a confirmed fit. When this hitch is installed it hangs below the front bumper like what you can see in the attached picture.

view full answer...

Answer 12

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Grille Guard and Front Hitch that Fits 2016 Ford F-150

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching