Replacement Base Linch Pin for Roadmaster Sterling Tow Bar

Question

Question:

I am looking for replacement spare Base Pins W/chain and clip for a Sterling Allterrain. I have a 2008 Honda CRV and the pin I have is 3/4 dia by 4 long from flange to tip. the RM-910029 says it is 7/8 dia by 3 3/4 long. what am I missing. What is the real part for my bracket? I can find one that is 3/4 dia X 4 long. Thanks

asked by: Bill N

0

Expert Reply:

The pin you need is part # RM-910008-00. The diameter is .74 inches and the length is 4 inches from the flange to the tip, as measured with a digital caliper.

expert reply by: Mike L

0

Answer 1

Yes we do. Depending on which pins you are referring to you would either need the Roadmaster Linch Pins #RM-910024. Or you would need the Roadmaster Replacement Base Pins with Chains and Clips part #RM-910029.

view full answer...

Answer 2

I have heard back from my contacts at Roadmaster about the pin you were needing. Part #RM-910008-00 which is the 5/8 inch diameter Linchpin and Chain is the correct replacement for your Falcon Tow Bar.

view full answer...

Answer 3

The correct lynch pins to use with the Roadmaster Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters #RM-910044 is the #RM-910024. These are sold in a pair.

view full answer...

Answer 4

The Roadmaster Linch Pins part #RM-910024 has a shaft diameter of .308" and length of 1.537" from the end of the pin to the bottom of the retaining nut

view full answer...

Answer 5

You can use the Blue Ox Aladdin Tow Bar with the Roadmaster Direct-Connect Base Plate Kit - Removable Arms part #RM-524454-5 for the 2015-2018 Ford Edge 3.5L V6 with the Roadmaster to Blue Ox adapter part #BX88185. This adapter is compatible wit the…

view full answer...

Answer 6

By the photo you kindly provided, you have a nearly complete Roadmaster Base Plate Quick Disconnect Assembly. It looks like you're missing at least one linchpin, part #RM-910024. According to my Roadmaster representative, the #RM-032 adapter is…

view full answer...

Answer 7

The top linch pins on the Replacement Quick Disconnect Crossbar Assembly #910021-00 you referenced can be found as a quantity of 2 on our site with part #RM-910024.

view full answer...

Answer 8

Both the old Falcon 5250 tow bar and the current Falcon 2 #RM-520 will work with the same crossbar assembly part #RM-067. So if you already have the Roadmaster crossbar you should not need any additional parts to bring it together with the Falcon…

view full answer...

Answer 9

You are correct with the part you will need in order to convert your Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar for Blue Ox Base Plates #RM-677 for use with your Roadmaster direct connect base plates, which are two of the swivel ears: -…

view full answer...

Answer 10

As indicated in the provided photo, the holes in the removable drawbars of the Roadmaster #RM-521424-5 base plate kit accept a 3/4 inch diameter pin, such as part #RM-910029 so the holes are actually fractionally larger than 3/4 of an inch. According…

view full answer...

Answer 11

The pin hole on the removable arms of the (discontinued) Roadmaster EZ5 base plate kit for your 2015 Chevrolet Equinox, is 3/4 inch. This is also true for the Roadmaster Direct-Connect Base Plate Kit #RM-523193-5, which is the new version, that uses…

view full answer...

Answer 12

Quality-wise, both tow bars are equivalent. Both have the same 6,000 lb capacity, but the StowMaster #RM-501 is a car-mount and the Falcon 2 #RM-520 is a motorhome mount. The Stowmaster connects to the motorhome via a coupler installed on the tow…

view full answer...

Replacement Base Linch Pin for Roadmaster Sterling Tow Bar

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching