Roadmaster Falcon Tow Bar Base Pin Needed

Question

Question:

I have a Roadmaster Falcon 5250 8-10 years old tow bar and need new base pins. The inside measurement on the tow arm is 3/4. The pins on your site are 7/8 and 5/8. Would there be a 3/4 pin available?

asked by: Peter C

0

Expert Reply:

I have heard back from my contacts at Roadmaster about the pin you were needing. Part # RM-910008-00 which is the 5/8 inch diameter Linchpin and Chain is the correct replacement for your Falcon Tow Bar.

expert reply by: Mike L

0

Answer 1

Both the old Falcon 5250 tow bar and the current Falcon 2 #RM-520 will work with the same crossbar assembly part #RM-067. So if you already have the Roadmaster crossbar you should not need any additional parts to bring it together with the Falcon…

view full answer...

Answer 2

Yes we do. Depending on which pins you are referring to you would either need the Roadmaster Linch Pins #RM-910024. Or you would need the Roadmaster Replacement Base Pins with Chains and Clips part #RM-910029.

view full answer...

Answer 3

The correct lynch pins to use with the Roadmaster Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters #RM-910044 is the #RM-910024. These are sold in a pair.

view full answer...

Answer 4

The top linch pins on the Replacement Quick Disconnect Crossbar Assembly #910021-00 you referenced can be found as a quantity of 2 on our site with part #RM-910024.

view full answer...

Answer 5

By the photo you kindly provided, you have a nearly complete Roadmaster Base Plate Quick Disconnect Assembly. It looks like you're missing at least one linchpin, part #RM-910024. According to my Roadmaster representative, the #RM-032 adapter is…

view full answer...

Answer 6

You can use the Blue Ox Aladdin Tow Bar with the Roadmaster Direct-Connect Base Plate Kit - Removable Arms part #RM-524454-5 for the 2015-2018 Ford Edge 3.5L V6 with the Roadmaster to Blue Ox adapter part #BX88185. This adapter is compatible wit the…

view full answer...

Answer 7

You are correct with the part you will need in order to convert your Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar for Blue Ox Base Plates #RM-677 for use with your Roadmaster direct connect base plates, which are two of the swivel ears: -…

view full answer...

Answer 8

The pin you need is part #RM-910008-00. The diameter is .74 inches and the length is 4 inches from the flange to the tip, as measured with a digital caliper.

view full answer...

Answer 9

As indicated in the provided photo, the holes in the removable drawbars of the Roadmaster #RM-521424-5 base plate kit accept a 3/4 inch diameter pin, such as part #RM-910029 so the holes are actually fractionally larger than 3/4 of an inch. According…

view full answer...

Answer 10

The Roadmaster Linch Pins part #RM-910024 has a shaft diameter of .308" and length of 1.537" from the end of the pin to the bottom of the retaining nut

view full answer...

Answer 11

The pin hole on the removable arms of the (discontinued) Roadmaster EZ5 base plate kit for your 2015 Chevrolet Equinox, is 3/4 inch. This is also true for the Roadmaster Direct-Connect Base Plate Kit #RM-523193-5, which is the new version, that uses…

view full answer...

Answer 12

Without knowing the diameter or your holes and the thickness of your chain loops, I can only give you some accessory options like S-Hook with Wire Keeper #C81830, S-hooks like #6495-716-33, and clevis hooks like #RM-910031. The best option is the…

view full answer...

Roadmaster Falcon Tow Bar Base Pin Needed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching