Interior RV Light Recommendation to Replace Liteco 179 Interior Light

Question

Question:

I currently have a 2005 holiday rambler with liteco model 179 ceiling lights. One of the ballasts went out and I was hoping you could give me some direction as to which if any of your lights would be suitable replacements. Thank you

asked by: Joshua A

0

Expert Reply:

I looked up the dimensions of your Liteco 179 interior light and the closest thing we have to it would be the part # ILL06COB which will be 11 inches by 4 inches. Your current light is 19-1/2 inches by 6-1/2 inches so this would be a bit smaller but the LED lights of this kit would provide a great deal of lighting.

expert reply by: Jameson C

0

Answer 1

I recommend replacing your lights with the LED RV Dome Light w/ Switch #RVILL50. These LED lights will outlast and use less power than the florescent tube lights in the Liteco 179 that you currently have. These lights are 15-3/4" long x…

view full answer...

Answer 2

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured…

view full answer...

Answer 3

Thanks for the information! The Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter item #RP85FR you were looking at fits the Lippert 1621, 1716, 0719, Rhino, and Fabex PB 600 series pin boxes. In order to verify this will replace your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...