Will Brophy Stake Pocket Mounted Camper Tie Downs Fit a 2007 Toyota Tundra

Question

Question:

Would the stake pocket tiedowns work on a 2007 Toyota Tundra? Looking at a popup camper.

asked by: Don

0

Expert Reply:

We had a customer use Brophy Stake Pocket Mounted Camper Tie Downs # TDSF on a 2005 Toyota Tundra and they worked but that was the generation before yours. Brophy doesn't provide a fit list but only states that they fit most full-size, non-dually pickup trucks with straight fenders and single-wall construction. The orange truck in the pictures is a perfect example.

For these tie downs we also recommend hardware kit # TDHP.

Another option is custom tie downs that mount to the truck frame. I have included a link to the main page for these tie downs that fit the 2007 Tundra. Just select the proper configuration on that page using the drop down menu.

expert reply by: Michael H

0

Answer 1

I reached out to Brophy to check into this for you. The Brophy Clamp On Camper Tie-Downs #HSWB are tested on domestic, full size bed trucks only so while these have worked on Toyota Tundras before, the double cab may be a challenge here. The tie…

view full answer...

Answer 2

I attached a picture that shows the instructions we have for the Tie Downs part #HSAB that you referenced. We've haven't seen them be an issue on a 2001 Ford F-150, but if you could get me a picture of what your setup looks like I can see if…

view full answer...

Answer 3

It is very likely the Brophy Clamp On Camper Tie-Downs - Bed Mount #HSAB will fit your 1999 Dodge Ram 2500 with an 8 foot bed, but because this is a universal fit, there isn't any specific fit information for your truck, though I can help you…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

You'll need to do some slight measuring to ensure the fit of the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV on your 4WD 2022 Ford F-350 FX4 dually. Just measure from the top of the rear axle to the top of the jounce…

view full answer...

Answer 12

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...