Brake Controller Recommendation for 1998 Isuzu Trooper Towing Camper Trailer

Question

Question:

I have a 1998 Isuzu Trooper and will be towing a RV trailer with 2 axles weighing 3,200 pounds dry. Which brake controllers would you recommend?

asked by: David B

0

Expert Reply:

The brake controller I recommend for you is the Tekonsha Prodigy P2 Trailer Brake Controller # 90885. This brake controller works to apply the trailer's brakes proportionally to the brakes of your 1998 Isuzu Trooper, helping the trailer brake smoother and causing less wear and tear on both the trailer and your vehicle. The P2 also features a digital display, 3 boost levels, battery protection, and continuous diagnostics. This controller is designed to work with trailers that have up to 4 axles with brakes, so it will certainly work well for your dual axle trailer. I've attached a review video of this brake controller for you.

To install the brake controller on your Trooper, you will first need a 4-Way flat trailer wiring harness, such as # C55339 if your vehicle does not already have a connector. After the 4-Way connector, you will want to install a 7-Way trailer connector. For a kit that includes everything needed to install the 7-Way connector and brake controller, the # ETBC7 kit is a great option. The linked instructions for this kit will walk you through the installation of the kit and the brake controller.

expert reply by: Victoria B

0

click to enlarge

Answer 1

A trailer light with 3 wires, like #RVSTL0060, that are black, white, and green generally the black wire is for running lights, green is for stop and turn signal, and white is for ground. If the old light on your trailer only used 2 wires, then it…

view full answer...

Answer 2

It sounds like you either have a blown fuse or a short on the right side turn light and brake light circuit. First, I recommend checking the trailer wire connector on the vehicle. You can use a circuit tester, like #PTW2993, to test that power is…

view full answer...

Answer 3

You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...