5th Wheel Installation Kit for B&W Patriot Hitch in 2010 Ford F-150

Question

Question:

I have 1 2010 f150 4 door which kit do i need to install a patriot 5th wheel

asked by: Terence H

0

Expert Reply:

The B&W Patriot 18K Sliding Fifth Wheel Hitch # BWRVK3270 install in your 2010 Ford F-150 with 6-1/2-foot bed using base rail kit # BWRVR3201-00. If you have the 8-foot bed then you can use the fixed (non-sliding) Patriot 16K hitch # BWRVK3200 or the 18K version # BWRVK3255. All will fit the same install kit.

For a wiring harness in the truck bed use part # PK11893-11932 from Pollak.

expert reply by: Adam R

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 5

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 8

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 9

I went ahead and checked with Curt and and the Curt Double Lock, Flip and Store Underbed Gooseneck Hitch #C60722 is the correct fit for a gooseneck on your 2001 Ford F-150. Having said that, your truck does need to have the holes in the side rails,…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 12

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...