What Diameter Shaft Will Fit Dutton-Lainson Removable Wheel With Pin For 1981 Boat Trailer Jack

Question

Question:

I need a new wheel for my 1981 boat trailer I purchased with my Sea Swirl 18 140 HP I/O Bow Rider Boat. What is the diameter of the shaft that will fit into this wheel? I like the pin idea. When I find the right one Ill drill the shaft to accept the pin. That is of course you say it will be OK. Many thanks for your help. Best regards,

asked by: Dennis F

0

Expert Reply:

I walked out to our warehouse and measured the inside diameter of Removable Wheel with Pin, part # DL22539 and it measured 2 inches. Part # DL22539, will fit a shaft with diameter of 2 inches.

Yes, you will be able to drill out a hole for the pin of part # DL22539 to fit the shaft of the jack on your 1981 Boat Trailer, if there is not a hole already there.

expert reply by: Reno H

0

Answer 1

The direct replacement for your Dutton-Lainson 203925B jack would be part #DL22560. According to Dutton-Lainson, the jack would indeed be compatible with your existing mounting plate. I've linked to a product demonstration video featuring the…

view full answer...

Answer 2

We have one wheel that you may be able to use, which is the Removable Wheel for Dutton-Lainson A-Frame Trailer Jack Model 6418 #DL22414. This is designed for the Dutton-Lainson DL22530 which has a 1-3/4" diameter inner tube. However, since it…

view full answer...

Answer 3

The Removable Wheel for Dutton-Lainson A-Frame Trailer Jack Model 6418 #DL22414 is compatible with the A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson #DL22530 which has an outer diameter tube 2 inches and the inner diameter at 1-3/4…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

I apologize for the confusion. It sounds like you have found some conflicting answers in the past, so I took the liberty to contact Bulldog directly and this is what they said: "The 12k RAM jack has a smaller diameter cross-shaft, therefore the…

view full answer...