Mounting Stromberg Carlson # 2020-JR Propane Tank Rack

Question

Question:

Can the rack be mounted off the floor so that the bracket only supports the tank?

asked by: John

1

Helpful Expert Reply:

It sure can. The # 2020-JR propane tank bracket is strong enough to support a full 20 lb propane tank. It's not necessary to set it on the floor. This assumes that the surface you attach the rack to is capable of supporting the weight of the tank plus that of the rack.

expert reply by: Mike L

1

Answer 1

To have a propane tank mounted on the outside of a trailer would be something you would want to check with your local DOT on. Most likely they wouldn't want you mounting a propane tank anywhere that would allow it to get hit in the event of…

view full answer...

Answer 2

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 3

We do have one option for holding a single 20 lb propane tank, which is from Stromberg Carlson. - Single-Bottle Liquid Propane Gas Rack #2020-JR I have added a link below to a video review for you to check out as well.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a great…

view full answer...

Answer 8

If your switch is illuminated then I do believe that 3rd terminal is for the backlight. For a replacement I recommend checking out the Single Rocker Switch - 12V - On/Off - SPST - Black Plate with Red Illuminated Switch #37212525. Attached is a…

view full answer...

Answer 9

I have a solution for you because as you know what you have now cannot charge Lithium batteries. You will need the Progressive Dynamics #PD4135K which is designed to replace your WF-8735P and is compatible with Lithium batteries. When this is…

view full answer...

Answer 10

We do have replacements for a Coleman Mach Air AC. There are a couple of options for 13,500 Btu or 15,000 Btu units in either Black or White: For black you will want the Advent Air Replacement RV Air Conditioner for Coleman Setup - 15,000 Btu item…

view full answer...

Answer 11

The 12V wire at the vehicle-end trailer connector being hot even when the truck is off can vary depending on the application. For all aftermarket hardwiring installations of a 7-Way wiring harness, the 12V wire will be hot at all times, even when the…

view full answer...

Answer 12

The light that indicates that the 12 volt circuit is hot is normal and it will not drain the battery. Think of it as the battery having a really long positive terminal that just extends to the rear of the vehicle. If nothing is drawing power from it,…

view full answer...