Recommendations for Brackets to Mount CE Smith Trailer Fenders # CE19504-2

Question

Question:

Which fender mounting bracket is needed for this fender, CE19504-2? Thanks

asked by: Michael C

0

Expert Reply:

For the set of CE Smith trailer fenders # CE19504-2 you can use existing brackets on the trailer or, if you need brackets, you can use # CE26098G-2. Drilling will be required for installation.

expert reply by: Michael H

0

Answer 1

You can mount the fenders directly to the trailer frame through the fender skirt on the back of the fender. I would recommend using large washers if you drill through the fender skirt and attach the fender directly to the trailer frame. If mounting…

view full answer...

Answer 2

I was informed by CE Smith that you will need to use the Mounting Brackets #CE26098G-2 to properly attach the CE Smith Single Axle Trailer Fenders w/ Top and Side Steps #CE19504-2.

view full answer...

Answer 3

When it comes to installing The CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 13 inch Wheels - Qty 2 #CE19503-2 you will need The Mounting Brackets for Trailer Fender - 13 inch/14 inch/15 inch Wheels - Galvanized Steel…

view full answer...

Answer 4

For what you listed the best fender solution is the part #CE17720 as it measures 22-1/2 inches long and is 7 inches wide. Since the sidewall of the tire is tapered from the top of the tread this would match the width needs you mentioned as well.

view full answer...

Answer 5

I have attached a photo for you of the Fulton Single Axle Trailer Fender part #F008595-2 which you can use to determine compatibility with your trailer. That said, it would really be hard for me to give you a definitive yes or no answer. The issue…

view full answer...

Answer 6

Since you have 14" diameter wheels you will want to use the CE Smith Single Axle Trailer Fenders #CE19504-2 that are designed for that size and have an inside length of 29-11/16". These fenders allow you to use your existing mounting…

view full answer...

Answer 7

The Fulton Single Axle Trailer Fenders #F008595-2 are going to be the closest fenders in size and design to the EZ Loader 250-023712-11 fenders you are looking for. These fenders are 10-1/4" wide x 45" long x 14-7/8" tall while the EZ…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Recommendations for Brackets to Mount CE Smith Trailer Fenders # CE19504-2

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching