Replacement Trailer Fenders For Shorelander Single Axle Trailer

Question

Question:

My trailer is a Shorelander single axal. The galvanized mounting angles are 30.5 inches apart. Will these bolt on?

asked by: James P

0

Expert Reply:

I was informed by CE Smith that you will need to use the Mounting Brackets # CE26098G-2 to properly attach the CE Smith Single Axle Trailer Fenders w/ Top and Side Steps # CE19504-2.

expert reply by: Bud M

0

Answer 1

The CE Smith Single Axle Trailer Fender with Top and Side Steps - Black Plastic - 14" Wheels, has a mounting point that measures, from center to center, 34-1/2 inches. These fenders come in either a quantity of one or two: - Quantity of 1:…

view full answer...

Answer 2

We have a very close option with the #CE19503-2 which is off by only 1/4 of an inch to the measurements you listed. It measures 29-3/4 inch for the inside portion and 33-3/4 inch for the outside portion.

view full answer...

Answer 3

The mounting bracket dimensions between the CE Smith #CE19504 and the Fulton #F008594 that you referenced are both very similar. They are close enough that they would be interchangeable. The dimension on the Fulton is 30-1/4 inches whereas on the…

view full answer...

Answer 4

The CE Smith Single Axle Trailer Fender w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 1 #CE19504 is my recommendation for you. It is 43-1/8 inches long x 11 inches wide x 12-1/2 inches tall which will give you a skirt height of…

view full answer...

Answer 5

I went out to our warehouse for you and measured the CE Smith Single Axle Trailer Fender part #CE19504-2. The inside width at the bottom is around 10-3/4" and then 9-1/2" at the top.

view full answer...

Answer 6

The CE Smith Single Axle Trailer fender #CE19504 is designed to be used with 14 inch trailer wheels. The mounting brackets that you will need are #CE26098G-2. These L-shaped brackets are made of galvinized steel and sold in pairs. You will need two…

view full answer...

Answer 7

The CE Smith Single Axle Trailer Fenders w/ Top and Side Steps #CE19504-2 actually does not have any pre-drilled holes for mounting brackets, so you will need to drill the holes yourself to match your existing brackets. The #CE19504-2 measures of…

view full answer...

Answer 8

I went out to our warehouse to take a couple measurements on the CE Smith Single Axle Trailer Fender #CE19504 that you referenced. The inside arch between the two side steps measures 30-5/8 inches long. The step itself which I believe is what you…

view full answer...

Answer 9

There is a slight difference in the designs of the Fulton fender #F008584 and the CE Smith Fender #CE19504 but other than appearance there isn't a whole lot of difference. I have stood on a Fulton fender before and it did flex but it didn't…

view full answer...

Answer 10

The CE Smith Single Axle Trailer Fenders #CE19504-2 were never intended to be mounted in this type of fashion, but it looks like it could be doable but will require modification. I recommend considering install some Steel Tandem Fenders #HP44VR.…

view full answer...

Answer 11

For the set of CE Smith trailer fenders #CE19504-2 you can use existing brackets on the trailer or, if you need brackets, you can use #CE26098G-2. Drilling will be required for installation.

view full answer...

Answer 12

You can mount the fenders directly to the trailer frame through the fender skirt on the back of the fender. I would recommend using large washers if you drill through the fender skirt and attach the fender directly to the trailer frame. If mounting…

view full answer...

Replacement Trailer Fenders For Shorelander Single Axle Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching