2009 Toyota Tacoma Hitch Installation Question

Question

Question:

Is there a hitch for my truck that does not require me to remove my bumper in order to install it?

asked by: ED J

0

Expert Reply:

The bumper does not need to be removed when installing the Curt Trailer Hitch Receiver - Custom Fit - Class III part # 13323 on a 2009 Toyota Tacoma, but three of the bolts that hold the bumper in place will need to be loosened and two will need to be removed in order to properly mount the hitch. The loosened bolts will be re-tightened and the removed bolts will be replaced by supplied bolts upon completion of the installation.

Because the bumper will not be properly mounted during this install it will be necessary for you to support the bumper to prevent it from dropping down.

In order to complete your towing setup you may also need a Tow Ready Custom Fit Vehicle Wiring for the 2009 Toyota Tacoma part # 118496. and a Trailer Hitch Ball Mount - 3/4 inch Rise or 2 inch Drop, 7,500 lbs part # C45010. For a trailer ball, use # 19260 for a 1-7/8 inch ball or # 19247 for a 2 inch ball. And pin and clip # PC3.

I have linked you to the recommended parts, as well as install details and an install video for the recommended hitch.

expert reply by: Jameson C

0

Answer 1

If you have a working 4 pin trailer connector and a boat trailer with surge brakes, then you will not need a 4-pin wiring harness. If your trailers 5-pin connector is the flat style you can use the 4 Pole to 5 Pole Trailer Wiring Adapter, part…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 7

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 11

The trailer hitch I recommend for a 2023 Hyundai Tucson is the Curt Trailer Hitch Receiver part #C94WR which I confirmed as a fit with Curt for all models, including the Hybrid. This trailer hitch features a bolt-on installation so there is no…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

2009 Toyota Tacoma Hitch Installation Question

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching