Recommended Hitch, Wiring, and Trailer Towing Setup for a 2015 Mazda CX-5

Question

Question:

hi, i need to modify a 2015 cx-5 for a trailer. im thinking of adding that curt class iii hitch c13127 that you showed in your very helpful video. is the hitch all that needs to be added or are there wires or whathaveyou that i would also need to buy? im sure i can do the install im fairly handy with a wrench but just want to make sure i have everything i need. thanks!!!

asked by: Rafe D

0

Expert Reply:

Good news, I can help make sure you have everything you need to tow your trailer.

The Curt Class III hitch # C13315, you were looking at does install easily, but I would recommend the Draw-Tite Class III hitch # 76138 instead.

Depending on if your trailer has brakes or not will determine which wiring you will need. Most small utility trailers or jet ski trailers will use a simple 4-way. For lights that are LED or not you will want the wiring harness # 118563. This will power the lights on your trailer. I have linked an installation video of how this installs to your vehicle as well. If your trailer has brakes you will need a 7-way like the # ETBC7 and a brake controller like the # 90195 to actuate them.

Other items you will need when towing a trailer is a ball mount and ball. This will depend on the trailer and your vehicle. I have linked a Help Article that will show you how to measure for the right rise or drop to determine the proper ball mount and ball for your vehicle and trailer. Since you do not have the hitch already installed on your vehicle, I can tell you that the inside height of the Curt # C13127 is 13-1/4 inches and the Draw-Tite # 75217 is 12-1/4 inches.

We do offer a common ball mount kit # 989900. We have determined through customers that these are the most common ball mounts and balls purchased. For added security customers will also purchase a hitch lock like # e98880 and a coupler lock like # 2847DAT.

I have linked all the above mentioned products to this page for your viewing and purchasing convenience.

expert reply by: Jackie C

0

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver part #76138 is a great option for a 2016 Mazda CX-5. In regards to install, you don't need to worry about angles or measurements, it uses preexisting holes in the frame so the hard work is done for…

view full answer...

Answer 2

If your 2016 Mazda CX-5 was made on May, 16th 2016 then you have a 2016.5 mid-year model as the cutoff date for prior mid-year models was April 1st, 2016. However, none of that matters when choosing a trailer hitch for your CX-5 as the Curt Trailer…

view full answer...

Answer 3

The hitch is rated independent of the vehicle so with the 2014 Mazda CX-5 owners manual specifying a lower 200 lb capacity, that will be the max capacity including the carrier weight. The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black…

view full answer...

Answer 4

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56310 is in fact the correct trailer wiring kit for your 2016.5 Mazda CX-5. It will work with the LED lights on your trailer. I have attached a video of this kit being…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...