Replacement Pivot Pin Recommendation for a Reese 15k Fifth Wheel Hitch

Question

Question:

I am looking for a pivot pin for a 15k reese 5th wheel. I see you have one listed for the 16k are they interchangeable? The diameter of my pin is 1 1/2 in and 4 in long.

asked by: Becky

0

Expert Reply:

Yes, the pivot pin part # 58484 that you referenced will fit your Reese 15k fifth wheel hitch. Reese up-rated their 15k hitches a few years back so the parts for a 16k are going to be the same as a 15k.

expert reply by: Jameson C

0

Answer 1

Any 3/4 ton or 1 ton (250/350 or 2500/500) is going to be able to handle the weight of your 5th wheel trailer without a problem. This trailer is actually on the light side as far as 5th wheels go, but I imagine that the weights you have given are the…

view full answer...

Answer 2

Sounds like you have a set of Lippert Ground Control Leveling Jacks #LC358590 on your trailer which would require the replacement foot part #LC377962 if that's what you are in need of. This is for round legs that have a pin in them.

view full answer...

Answer 3

The rubber bumpers on the head of a 5th wheel trailer hitch like the Pro Series 16k, #PS30096, are designed to prevent and/or limit contact between components on the hitch. You can install 2 more but really only 2 are needed. Adding 2 more can limit…

view full answer...

Answer 4

The Replacement Rubber Bumper for Reese Fifth Wheel Trailer Hitch, part #30536, attaches to the head with a screw that gets pressed down through the top of it and then is attached on the underside of the head with a nut. I have provided links to the…

view full answer...

Answer 5

It sounds like you are talking about #58089. But the L shaped one I am not sure of unless it is part of the handle that got caught in the elbow of the handle and formed an L. Like part #58094. For the bumpers, on Reese model 5th wheel hitches there…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Replacement Pivot Pin Recommendation for a Reese 15k Fifth Wheel Hitch

Product Page this Question was Asked From

Continue Researching